What to look at in live data
With P0100 the ECU finds the mass air flow circuit wrong in general: signal missing, impossible, or not moving with rpm. In the standard data, watch air flow in grams per second: with the ignition on and the engine off it should be zero or close, with the engine running it should be there and change instantly with every throttle blip. If it sits on one value, or shows air with the engine off, the signal can't be trusted.
When they discard the mass air flow sensor, many ECUs calculate air from rpm and manifold pressure: the engine still runs, but with little pull and higher consumption, and the air flow reading may stay stuck on a substitute value. Check power and ground at the sensor connector and the air intake: a wet air filter, or a sensor coated with oil after an over-oiled sports filter, gives strange signals even before it fails.
How serious is it, can you drive?
Severity is medium. You can drive gently: the engine runs on backup values, worse than usual. It's worth fixing soon, because a mixture that's only estimated uses more fuel over time and, on diesels, clogs the DPF and EGR sooner.
Read P0100 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The mass air flow sensor, or MAF, sits on the duct between the air filter and the engine. The ECU uses its reading to decide how much fuel to inject. With P0100 that signal is missing or electrically wrong: a broken wire, a short, no supply.
That's different from P0101, where the circuit works but the values aren't believable, often because of dirt or an air leak. With P0100 the ECU stops trusting the sensor and runs the engine on backup values worked out from revs and throttle.
Symptoms
- Engine light on.
- The engine hesitates under acceleration and has less pick-up.
- Rough idle, sometimes stalling when you lift off.
- Higher fuel consumption; on diesels black smoke and sometimes limp mode.
Most likely causes, in order
- The MAF connector unplugged, half-seated or corroded, often after work on the air filter.
- The wiring to the sensor broken or pinched.
- A failed sensor internally.
- Missing supply to the sensor, from a fuse or relay.
What to check before the garage
- The MAF connector, on the duct after the air filter: it must click fully home and be clean.
- Whether the air filter was changed recently: a forgotten connector or a duct fitted crooked is the classic case.
- Whether P0113 shows up too: on many cars the MAF also contains the intake air temperature sensor, and the shared connector is the first suspect.
- If you want to clean the sensor, use only dedicated MAF spray, never cloths or compressed air.
At the garage: what to ask for
A live reading of the MAF signal and a measurement of supply, earth and signal at the connector, to tell whether the fault is in the wiring or the sensor. The connector costs little; a new sensor costs more, but on many cars it's a few minutes' job.
What DrivePulse shows
DrivePulse reads P0100 and opens its card, with the advice to start from the connector and only clean the sensor with the right spray; it also tells you whether the code is pending or confirmed.
In the live data, on cars that report it, you find the MAF air flow: a value stuck at zero or one that doesn't rise with revs confirms the circuit problem. If P0101 or P0113 show up too, DrivePulse lists them together.
Frequently asked questions
Can I drive with P0100?
Yes, gently: the engine runs on backup values. Better to fix it soon, because consumption and dirt build up.
What's the difference from P0101?
P0100 is an electrical fault in the MAF circuit. P0101 says the circuit works but the values aren't believable.
Will cleaning the MAF fix P0100?
Rarely: P0100 is usually a connector, wiring or failed sensor problem. Cleaning helps more often with P0101.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.