What to look at in live data
The typical sign of P0113 in the data is an impossible intake air temperature, often around -40 °C: that is what the ECU reads when the circuit is open. After the car has stood overnight, intake air should be close to the outside temperature and to coolant temperature.
If the value is right but now and then jumps to -40 °C, the contact is intermittent: with the engine off and the ignition on, gently move the sensor connector and cable and see whether the value jumps. If it stays at -40 °C all the time, the circuit is open: a loose connector, a broken wire or a failed sensor.
How serious is it and can you drive?
Severity is low. You can drive normally: the ECU uses a backup value for air temperature. It's still worth fixing, because while the light is on for this code you won't notice if a more serious one arrives.
Read P0113 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The intake air temperature sensor measures how cold or warm the air entering the engine is: cold air is denser and needs more fuel. It's often built into the air mass sensor or fitted in the duct just after the filter.
The sensor changes resistance with temperature. With P0113 the ECU sees a voltage that's too high, which corresponds to impossibly cold air, the typical reading of an open circuit: an unplugged connector, a broken wire or a failed sensor.
Symptoms
- Often just the light.
- Slightly harder cold starts.
- Slightly higher fuel consumption.
- In the live data, an absurd air temperature, far below freezing even in summer.
Most likely causes, in order
- An unplugged or loose connector, often after an air filter change or from vibration.
- A broken wire or a corroded contact in the connector.
- A failed sensor. If it's inside the air mass sensor, sometimes the whole part is replaced.
What to check before the garage
- If you've recently changed the air filter, check that every connector on the filter box and duct is plugged in.
- Look at the sensor connector: it should click fully home, with no corrosion on the contacts.
- Make sure the wires aren't stretched or pinched by the filter lid.
At the garage: what to ask for
A resistance check of the sensor and a continuity test of the wires back to the ECU. If the connector is fine and the value is off, the sensor is replaced.
What DrivePulse shows
DrivePulse reads P0113 and opens its card, which tells you to check the connector first. The live Dashboard shows intake air temperature: if it reads an impossible value, far below freezing, the circuit is open.
After refitting the connector, the same reading tells you straight away whether it's back to normal, close to the outside temperature with a cold engine.
Frequently asked questions
Can I drive with P0113?
Yes, normally. The ECU uses a backup value. It's worth fixing so other codes don't hide behind the same light.
Why does air temperature read minus 40?
Because that's the value many ECUs show when the sensor circuit is open. It's the classic sign of an unplugged connector or a broken wire.
What's the difference from P0112?
P0112 is the opposite case: signal too low, usually a short. P0113 is signal too high, usually an open circuit.
Where is the sensor?
It depends on the car. It's often inside the air mass sensor, just after the filter box; on others it's a separate sensor in the intake duct or manifold. The connector can nearly always be reached without tools.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.