What to look at in live data
The oxygen sensor heater brings the sensor up to temperature quickly, and its effect shows in the data: after a cold start, watch how long it takes for the fuel system status to switch to closed loop. With a working heater it usually takes less than a couple of minutes; with P0030 the sensor ahead of the converter stays flat for much longer, and the ECU keeps running without its signal.
The rest is checked with a multimeter, with the engine cold and off: at the sensor connector the heater should show a low resistance (often a few ohms, depending on the sensor) and receive power with the ignition on. P0030 concerns the control circuit, so the wire to the ECU counts too, as does the heater fuse, which often feeds several sensors: if it blows, codes appear for all of them.
How serious is it, can you drive?
Severity is low: you can drive, the engine won't be damaged. The car does use a little more fuel and pollute more, though, and with the light on it won't pass its inspection. It's worth fixing without waiting too long.
Read P0030 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The heater gets power from a fuse or relay, and the ECU switches it on by completing the circuit to ground. While doing so, it checks that the current and voltage on the control wire are right.
With P0030 the control wire reads as open, shorted or with impossible values. On some cars the same kind of fault shows up as P0135: the part to check is the same, only the way the ECU describes it changes.
Symptoms
- Check engine light on, almost always with nothing else.
- Slightly higher fuel use in the first few minutes, until the exhaust gas heats the sensor.
- On some cars, a slightly less smooth idle when cold.
Most likely causes, in order
- The sensor's internal heater open: it's the most common fault, and the whole sensor is replaced.
- The sensor connector, under the car, corroded or melted by exhaust heat.
- The fuse or relay that powers the heaters.
- The sensor wires, burnt by the exhaust pipe or torn.
- An unsuitable sensor, with a heater different from the one the ECU expects.
What to check before the garage
- Wait until the exhaust is cold before going near it.
- Look at the first sensor's wires under the car: no melted parts, nothing loose or resting on the exhaust.
- Check in the handbook which fuse powers the sensors and see whether it has blown.
If the fault involves several sensors
If heater codes for other sensors, such as P0036 or P0141, appear together with P0030, it's unlikely they all failed at once. Far more likely the common supply is missing: a shared fuse, relay or connector.
In that case it's worth starting there, before replacing one sensor after another.
A new sensor has to be the right one
Each sensor's heater has a precise resistance, and the ECU knows it. A generic sensor, even with the same connector, can have a different heater: the ECU reads it as a fault and P0030 comes straight back after the replacement.
If the code returns with a freshly fitted sensor, the first thing to check is the part number.
At the garage: what to ask for
A measurement of the heater resistance and of the supply at the connector, and a check of the fuse and relay. In order of cost: fuse or relay, connector, wire repair, new sensor of the right type.
What DrivePulse shows
DrivePulse reads P0030 and opens the sensor heater card: you can drive, but with the light on the car won't pass its inspection; it also says whether the code is pending or confirmed. If other heater codes appear too, you see them in the same list.
In Health, the battery voltage helps rule out a weak electrical system. After the repair, Before the inspection tells you when the heater and oxygen sensor self-tests are ready again.
Frequently asked questions
Can I drive with P0030?
Yes: the engine won't be damaged. It uses a little more fuel and pollutes more when cold, and with the light on it won't pass its inspection.
What's the difference from P0135?
They concern the same heater: P0030 describes a fault in the control circuit, P0135 a heater fault. Some ECUs use one, some the other.
I replaced the sensor and the code came back: why?
Often the sensor isn't the right one for the car and has a different heater. Or the fault was in the fuse, the relay or the wires.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.