EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P0135

P0135: O2 sensor heater circuit, bank 1 sensor 1

The oxygen sensor before the catalytic converter only works well when it's very hot, and a small electric heater gets it there quickly. With P0135 the ECU sees that the heater isn't working. The car drives fine, but after every cold start the sensor takes longer to come into play.

Get DrivePulse

What to look at in live data

With P0135 the ECU sees that the heater of the first sensor, bank 1, isn't working as it should. In the standard data the clearest sign is how long the engine takes, after a cold start, to switch to closed loop: if it takes much longer than usual, or only gets there after a long stretch, the sensor is being heated by exhaust gas alone. Check the control module voltage too: with low voltage the heater heats less.

The difference between P0135 and P0030 is where the problem lies: the first is about how the heater works (current draw or warm-up time out of range), the second about the control circuit. In practice the checks are the same: heater resistance at the sensor connector with the engine cold, power with the ignition on, the fuse. If the heater is open, the whole sensor is replaced, because the heater is built into it.

How serious is it, can you drive?

Severity is low: you can drive with no immediate problems. It's worth replacing the sensor at the next opportunity, because meanwhile cold fuel use and emissions stay higher, and with the light on the car may fail its inspection.

Read P0135 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The ECU powers the sensor heater and checks its current. If the current is missing or outside the expected values, it logs P0135. Bank 1 sensor 1 means the sensor before the catalytic converter, on the side of the engine with cylinder 1.

The code is about the heater, not the part of the sensor that measures oxygen: that part may still be healthy. It's the same kind of fault as P0141, which concerns the sensor after the catalytic converter.

Symptoms

  • Check engine light on, often with nothing else.
  • Slightly higher fuel use, especially on short trips.
  • Sometimes a slightly unsteady idle in the first minutes after a cold start.
  • Higher emissions with a cold engine, which can count at an emissions test.

Most likely causes, in order

  • The sensor's internal heater gone open circuit: the most common cause, fixed only by replacing the sensor.
  • The fuse that feeds the heater.
  • The sensor wiring or connector, cooked by exhaust heat or damaged during other work.
  • Rarely, the driver circuit in the ECU.

What to check before the garage

  • The oxygen sensor heater fuse: the manual tells you which one, and on some cars it's shared with other sensors or the injectors.
  • The sensor connector, with the engine cold: fully seated, no corrosion, cable away from the exhaust.
  • With a multimeter, on the sensor side of the connector, the resistance of the two heater wires: if it reads open circuit, the heater has failed.

Why it affects cold fuel use

Until the sensor is hot, the ECU can't use it and meters fuel with safe, slightly richer values. With a working heater this phase is short; without it, the sensor has to wait for the exhaust to warm it, and on a short trip or in winter that may never happen.

Drivers who mostly do a few kilometres at a time notice it more, in fuel use and in exhaust smell.

At the garage: what to ask for

A measurement of the heater resistance and the supply at the connector before ordering the sensor. If the fuse blows again, look for a shorted wire. In order of cost: fuse, cable or connector repair, new sensor.

What DrivePulse shows

DrivePulse reads P0135 and opens its card, with the advice to check the dedicated fuse and replace the sensor at the next opportunity; it also says whether the code is pending or confirmed.

In live data, on cars that report it, watch the sensor before the catalytic converter right after a cold start: with a failed heater it takes much longer than usual to start switching. In Statistics, the time you spend with a cold engine tells you how much the fault affects the way you use the car.

Frequently asked questions

Can I drive with P0135?

Yes, with no immediate problems. It's worth replacing the sensor at the next opportunity, for cold fuel use and for the inspection.

What's the difference from P0141?

It's the same fault on different sensors: P0135 is the heater of the sensor before the catalytic converter, P0141 that of the sensor after it.

Can just the heater be repaired?

No: the heater is inside the sensor. If it has failed, the sensor gets replaced. First, though, check the fuse and the cable.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes