EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P0134

P0134: O2 sensor circuit no activity detected, bank 1 sensor 1

Once warm, the oxygen sensor before the catalyst keeps changing its signal while the ECU corrects the mixture. With P0134 that signal stays fixed at a middle value, as if the sensor weren't there. Often the sensor is cold because its heater doesn't work, or it's simply worn out.

Get DrivePulse

What to look at in live data

With P0134 the first bank 1 sensor shows no sign of life: with the engine warm and in closed loop a conventional sensor should switch several times a second between about 0.1 and 0.9 V, and instead it sits still around 0.45 V, the value the ECU sees when the sensor isn't working. Watch the fuel system status too: if it stays in open loop after several minutes with a warm engine, the ECU has stopped using it.

A sensor stuck at 0.45 V may be cold (failed heater: see whether P0030 or P0135 are there too), disconnected or dead. Hold the engine at 2,500 rpm for a minute to heat it properly and see whether it wakes up: if it starts switching, the problem is the heater; if it stays flat, check the connector and wires and then the sensor. An exhaust leak ahead of the sensor can confuse it, but it usually makes it read lean, not stay still.

How serious is it and can you drive?

Severity is medium. You can drive gently. Get it fixed soon: without the sensor the mixture is less precise, fuel use rises and in the long run the catalyst suffers. With the light on the car won't pass its inspection.

Read P0134 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

A working oxygen sensor on a warm engine swings quickly between «rich» and «lean»: that's the sign it's measuring. When cold, it stays at a middle voltage. That's why it has an electric heater that brings it up to temperature in moments.

With P0134 the ECU waits the expected time after starting and still sees the signal fixed. It then stores the code and meters the mixture without the sensor, on backup values.

Symptoms

  • Check engine light on.
  • Slightly higher fuel use, especially in town.
  • The engine sometimes less smooth at idle.
  • P0135, the heater code, often appears too.

Most likely causes, in order

  • A worn-out sensor or one with an open heater: it's the most common cause.
  • The heater fuse blown.
  • The sensor connector unplugged, melted or corroded, often under the car near the exhaust.
  • The sensor wires burnt or torn.

What to check before the garage

  • Wait until the exhaust is cold before getting close.
  • Look at the connector of the sensor before the catalyst: it should be clipped in, not melted and not resting on the exhaust.
  • Look in the handbook for the sensor heater fuse and check whether it's intact.

Cold sensor or dead sensor?

The two often look alike: a sensor that doesn't warm up stays as still as a dead one. If P0135 is there too, the first suspect is the heater, with its fuse and wires.

If the heater works and the signal stays fixed, the sensor is worn out. The repair almost always ends with a new sensor, which is usually also available as a universal part.

At the garage: what to ask

Reading the sensor signal live with a warm engine, measuring the heater, and checking the fuse and connector. In order of cost: fuse or connector, wiring repair, a new sensor.

What DrivePulse shows

DrivePulse reads P0134 and opens its card, with the advice to check the connector and fuse before replacing the sensor; it also tells you whether the code is pending or confirmed. If P0135 is there too, it lists them together.

In live data, on cars that report it, you'll find the sensor before the catalyst. With a warm engine and the car idling standing still, a healthy sensor keeps swinging; if it stays motionless mid-scale, that's the P0134 picture.

Frequently asked questions

Can I drive with P0134?

Yes, gently. Get it fixed soon: the mixture is less precise, fuel use rises and over time the catalyst suffers.

What's the difference from P0135?

P0135 says the sensor heater isn't working. P0134 says the sensor signal stays fixed: often precisely because the heater isn't warming it.

Do I need to replace the sensor?

Almost always yes, but it's worth checking the fuse and connector first. If the heater has power and the signal stays fixed, the sensor is finished.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes