EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P0141

P0141: O2 sensor heater circuit, bank 1 sensor 2

The oxygen sensor after the catalytic converter has a small heating element that warms it up quickly. With P0141 that heater's circuit isn't working. The engine runs as before; the catch is that the converter check comes late or not at all.

Get DrivePulse

What to look at in live data

The second sensor, the one after the catalytic converter, has a heater too, and with P0141 the ECU finds it faulty. In the standard data, watch the bank 1 sensor after the converter in the first minutes after a cold start: with a working heater it soon starts giving a steady value between 0.5 and 0.8 V; with a failed heater it stays low and flat for a long time, waking up only once the exhaust has heated it.

The engine runs as before, because the rear sensor mainly watches the catalytic converter: often the code is the sole sign of the fault. The check is electrical, with the engine cold: heater resistance at the sensor connector and power with the ignition on, with a fuse often shared with the first sensor. The connector sits under the car, near the exhaust tunnel, and suffers from water and salt.

How serious is it, can you drive?

Severity is low. You can drive without problems and replace the sensor when convenient. It's worth fixing before an inspection, though, and keeping an eye on the light: while it's on for P0141, a new and more serious code would go unnoticed.

Read P0141 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Oxygen sensors only work when hot. So they don't have to wait for the exhaust to warm them, they contain an electric heater that brings them up to temperature within moments of starting.

P0141 concerns sensor 2 on bank 1, the one after the converter, which is mainly there to check whether the converter is working. With the heater faulty, the sensor only warms up with exhaust heat, and the ECU may not complete that check.

Symptoms

  • Engine light on.
  • Usually no change in how the car drives or in fuel consumption.
  • At an inspection, the converter or sensor monitor may show as not ready.

Most likely causes, in order

  • An open heater inside the sensor: the most common fault.
  • The heater fuse blown.
  • The sensor connector corroded or unplugged, often under the car and exposed to water and salt.
  • The wiring damaged by exhaust heat or torn.

What to check before the garage

  • The oxygen sensor heater fuse, shown in the owner's manual.
  • If you can reach the connector of the sensor after the converter: clipped in, with no corrosion and the wires away from the exhaust.
  • Whether the code for the sensor before the converter shows up too: a shared fuse can switch off both heaters.

At the garage: what to ask for

A measurement of the heater resistance at the connector and a check of the supply and fuse. If the heater is open, the sensor is replaced; it's a separate part and usually a short job. In order of cost: fuse, connector or wiring, new sensor.

What DrivePulse shows

DrivePulse reads P0141 and opens its card, with the advice to start from the fuse and the reassurance that you can drive and replace it when convenient; it also tells you whether the code is pending or confirmed.

The Before the inspection card shows how many self-test monitors are ready, including the oxygen sensor and converter ones on cars that report them: after the repair you see when they're ready again.

Frequently asked questions

Can I drive with P0141?

Yes, without problems: the engine runs as before. It's worth fixing when convenient, before an inspection.

Does the sensor still work?

Yes, but it only warms up with exhaust heat, so later. That's why the ECU may not complete the converter check.

What's the difference from P0130?

P0130 concerns the signal of the sensor before the converter. P0141 concerns the heater of the sensor after the converter.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes