EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P2237

P2237: O2 sensor positive current control circuit open, bank 1 sensor 1

Many recent engines have a wideband oxygen sensor ahead of the catalytic converter, which measures the mixture precisely across a wide range. To do this the ECU sends it a regulated current on a dedicated wire. With P2237 that wire reads as open: the ECU can no longer measure the mixture properly.

Get DrivePulse

What to look at in live data

P2237 concerns wideband sensors, the ones that measure lambda instead of switching: the ECU controls the current the sensor works with and finds its circuit open. In the standard data, watch the bank 1 sensor ahead of the converter with the engine warm: a healthy sensor reads a lambda close to 1.00 at idle, moves a little with throttle blips and, on many cars, shows its current in milliamps moving around zero; with P2237 the value stays fixed, often on a round number, or is missing.

The fuel system status often stays in open loop even with a warm engine, because the ECU no longer trusts the sensor, and the fuel trims stay at zero. The fault is electrical: the sensor connector (often under the car, exposed to water and heat), wires cooked near the exhaust, an open sensor. Since a wideband sensor has five or six wires, check the connector against the wiring diagram before replacing it.

How serious is it, can you drive?

Severity is medium. You can drive gently, but have it checked soon: without a precise measurement the mixture can stay wrong for a long time, and in the long run that can ruin the catalytic converter. With the light on the car won't pass its inspection.

Read P2237 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

A wideband sensor doesn't just say 'rich' or 'lean': inside it has a cell that pumps oxygen, and the current needed to do so tells the ECU how far the mixture is from ideal. The ECU controls this current on a circuit of its own.

P2237 says the positive current circuit is open: a broken wire, a terminal that doesn't touch or a failed sensor cell. Without that measurement the ECU meters fuel using fallback values, which are less precise.

Symptoms

  • Check engine light on.
  • Higher fuel consumption and sometimes a slightly uneven engine.
  • A stronger exhaust smell than usual.
  • On some cars, slightly reduced power.

Most likely causes, in order

  • The sensor connector, under the car, corroded, melted or disconnected.
  • The sensor wires, burnt by the exhaust or torn.
  • A failed sensor, often old or contaminated by oil or coolant.
  • An intermediate connector between sensor and ECU with a spread terminal.
  • Rarely, the ECU.

What to check before the garage

  • Wait until the exhaust is cold before going near it.
  • Look at the first sensor's wires and connector: no melted parts, nothing loose or resting on the exhaust.
  • Listen for the exhaust blowing or making noise before the catalytic converter.

The wideband sensor and its wires

A traditional sensor usually has four wires; a wideband one has five or six, because besides the heater it needs the measuring cell circuit and the pump current circuit. Each circuit has its own codes: P2237 is about the positive current.

That's why at the garage the continuity of each wire between sensor and ECU is measured first. If the wires are fine, the sensor is almost always to blame.

At the garage: what to ask for

A continuity test of the wires between sensor and ECU, a check of the connector and a live reading of the sensor signal. Before replacing the sensor, it's worth ruling out a genuine mixture problem. In order of cost: connector, wire repair, new sensor of the right type.

What DrivePulse shows

DrivePulse reads P2237 and opens the oxygen sensor card, with the warning that a wrong mixture for a long time can ruin the catalytic converter; it also says whether the code is pending or confirmed.

If P0171 or P0172 appear too, DrivePulse lists them together. After the repair, Before the inspection tells you when the oxygen sensor self-test is ready again.

Frequently asked questions

Can I drive with P2237?

Yes, gently, but have it checked soon: a wrong mixture for a long time can ruin the catalytic converter.

What's the difference from P0130?

P0130 points to a general fault in the sensor circuit; P2237 points precisely to the positive current circuit, which only wideband sensors have.

Is replacing the sensor enough?

Often, yes, but the wire continuity must be checked first: if a wire is broken, the new sensor will set the same code.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes