EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P0105

P0105: manifold absolute pressure/barometric pressure sensor circuit

The MAP sensor measures the air pressure in the intake manifold: the ECU uses it to work out how much load the engine is under and to meter fuel and ignition timing. With P0105 the sensor's signal is missing or has impossible values. The cause is often simple: a hose that has come off or a loose connector.

Get DrivePulse

What to look at in live data

The standard data includes intake manifold absolute pressure and barometric pressure. With the engine off and the ignition on they should be almost the same, around 100 kPa at sea level and less in the mountains: it is the simplest check of the sensor. With the engine running at idle, manifold pressure on a naturally aspirated petrol engine usually drops to between 25 and 40 kPa, and rises at once with every throttle blip.

With P0105 the signal is missing, impossible or stuck: if manifold pressure doesn't move away from atmospheric with the engine running, look first at the vacuum hose to the sensor (where there is one), often cracked or loose, then at the connector and wires. On turbo engines the sensor sits after the intercooler, where oil and condensation can foul it: a value that is slow to respond is often just dirt.

How serious is it and can you drive?

Severity is medium. If the engine runs well, drive gently to the garage. If it stalls at idle or jerks, avoid junctions and overtaking and get it checked soon: the real risk is an engine cutting out in the middle of a manoeuvre.

Read P0105 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The MAP sensor sits on the intake manifold, or is linked to it by a rubber hose. The ECU powers it and gets back a voltage that changes with pressure: high with the engine off, low at idle, high again under full throttle.

With P0105 the ECU reports a fault in the circuit: the signal doesn't arrive or is outside any possible value. Without that figure the engine runs on backup values, so it runs worse but usually keeps running. On some cars the same sensor also reads the outside pressure as soon as you turn the key, which is why the name mentions barometric pressure too.

Symptoms

  • Check engine light on.
  • Rough idle or an engine that stalls.
  • Less power and higher fuel use.
  • Hard starting, especially when cold.

Most likely causes, in order

  • The vacuum hose to the sensor off, cracked or blocked: often that's all it is.
  • The sensor connector loose or corroded.
  • The sensor wires broken or shorted, or the sensor's power supply missing.
  • The sensor failed internally, or fouled with oil and soot.

What to check before the garage

  • With the engine off, find the sensor on the manifold and look at the rubber hose going to it: it should be pushed fully on, with no cracks.
  • Check that the connector is clipped all the way in and that the pins aren't green with corrosion.
  • With the engine running, listen for an air hiss from the engine bay: it means there's an air leak near the manifold.

Circuit or real pressure?

P0105 is about the circuit, meaning the electrical signal. If the signal arrives but doesn't match the engine load, the ECU stores P0106 instead, which points more towards an air leak or a dirty sensor.

That's why the first check is always the simplest one: hose and connector. The sensor gets replaced afterwards, if the fault stays, and it's usually an inexpensive part.

At the garage: what to ask

Checking the sensor's power supply and signal with a tester, and comparing the engine-off reading with the outside pressure. In order of cost: hose or connector, wiring repair, a new sensor.

What DrivePulse shows

DrivePulse reads P0105 and opens its card, with the advice to start from the vacuum hose and the connector; it also tells you whether the code is pending or confirmed.

In live data, on cars that report it, you'll find the manifold pressure (MAP). With the key on and the engine off it should be close to the outside air pressure; at idle, on a petrol engine, it drops a lot. If it stays fixed or makes no sense in both cases, the signal isn't getting through. It's a test to do with the car standing still.

Frequently asked questions

Can I drive with P0105?

If the engine runs well, yes, gently to the garage. If it stalls at idle or jerks, get it checked soon and avoid manoeuvres where you need full power.

What's the difference from P0106?

P0105 reports a fault in the sensor circuit: the signal is missing or impossible. P0106 says the signal arrives but doesn't match the engine load.

Do I need to replace the sensor?

Not first. Often refitting the vacuum hose or the connector is enough. The sensor is replaced if the problem stays, and it's usually an inexpensive part.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes