What to look at in live data
A mass air flow sensor that comes and goes shows clearly in the live data, if you watch it long enough: air flow in grams per second should follow rpm smoothly, with no gaps. Leave the engine idling and watch for a few minutes: sudden drops to zero or isolated spikes, with idle faltering at the same instant, are the sign of a contact opening.
Repeat the connector test while watching the value: if the gap appears every time you touch the connector or the cable, the cause is there and not in the sensor. If the fault shows only on the move, over bumps or with the engine hot, watch air flow over a stretch of rough road with the phone in the hands of the person in the passenger seat: a value that drops with each jolt confirms a bad contact in the wiring.
How serious is it, can you drive?
Severity is medium. You can usually drive gently to the garage. If the engine dies or suddenly loses power, avoid overtaking and tricky junctions until it's fixed.
Read P0104 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The ECU reads the MAF sensor constantly and knows what values to expect at each engine speed. If the signal drops to zero or jumps impossibly for a split second, then returns to normal, it logs P0104.
That's why the code talks about an intermittent fault: at the garage the sensor can look perfect, because the fault only shows under certain conditions. A permanent circuit fault is something else and has its own codes, such as P0100.
Symptoms
- A sudden hesitation when accelerating that goes away by itself.
- The engine suddenly dying at idle and restarting without trouble.
- Limp mode that appears and goes away after a restart.
- A check engine light that comes on, perhaps goes off after a few days, then returns.
Most likely causes, in order
- The MAF sensor connector, with corroded pins or a broken locking tab.
- The wiring rubbing against the engine or a bracket, with a wire that opens as the engine moves.
- The ground for the sensor or the engine, loose or corroded.
- The MAF sensor itself, with an internal fault that shows up with heat or vibration.
- Water getting into the connector, after rain or an engine wash.
The connector test
- With the engine off, unplug the MAF connector and look at the pins: they should be shiny, with no green or white corrosion, and the seal should be in place.
- Push it back until you hear the tab click.
- With the engine idling, gently move the cable near the connector without pulling: if the engine stumbles or changes note, you've found the spot.
- Follow the cable to where it runs near the engine or a bracket and look for worn sheathing.
Why it comes and goes
A weak contact works fine until something disturbs it. Engine vibration, heat expanding the parts and moisture are enough to break it for an instant: that's why the fault shows on rough roads, with a hot engine or on damp mornings, and vanishes when the car is parked at the garage.
Noting when it happens helps whoever does the diagnosis a lot: cold or hot, over potholes, after rain.
At the garage: what to ask for
A live reading of the MAF sensor while the wiring is moved, and a check of the sensor's power and ground. The sensor only gets replaced after ruling out the connector and wires. In order of cost: cleaning and securing the connector, repairing the cable, a new MAF sensor.
What DrivePulse shows
DrivePulse reads P0104 and opens the MAF sensor card, with the electrical causes and checks; it also says whether the code is pending or confirmed.
In live data, on cars that report it, you'll find the MAF reading: while driving the passenger watches it, and if it now and then drops to zero or jumps and comes back, that's the signal cutting out. With the engine running and the car standing still, you can do the cable test with that screen open.
Frequently asked questions
Can I drive with P0104?
Yes, gently. If the engine dies or suddenly loses power, avoid overtaking and tricky junctions until it's repaired.
What's the difference from P0100 and P0101?
P0100 is a fault in the MAF sensor circuit, P0101 a value outside what's expected. P0104 says the signal keeps coming and going.
Do I need a new MAF sensor?
Not at first: in most cases it's the connector, a wire or the ground. The sensor gets replaced after ruling those out.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.