EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Fuel vapour (EVAP)
  4. P0441

P0441: evaporative emission system incorrect purge flow

Petrol vapour collected in the charcoal canister has to be drawn into the engine and burnt. With P0441 the flow isn't what's expected: usually the purge valve is stuck.

Get DrivePulse

What to look at in live data

In the standard data, watch commanded evaporative purge, which is how far the ECU opens the canister valve, together with the short term fuel trim. With the engine warm, ideally after filling up when the canister holds plenty of vapour, the vapour reaching the engine enriches the mixture as soon as purge rises, and the short term trim should drop a little: if purge changes and the trim never moves, there is no flow.

The other way round, if idle turns rough or the trims drop a lot even with purge at zero, the valve is stuck open and lets vapour through when it shouldn't; the engine often struggles to restart after filling up. If the car reports evaporative system pressure, it should go slightly into vacuum during purge. Crushed or disconnected hoses between the valve and the intake set the same code.

How serious is it and can you drive?

Severity is low. You can drive normally. If the valve stays open, though, the mixture can get rich and the engine idle worse: it's worth fixing before other codes appear.

Read P0441 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Petrol in the tank gives off vapour that mustn't escape into the air: it goes into an activated charcoal canister. When the engine runs, the ECU opens a valve, the purge valve, and the engine draws the vapour from the canister and burns it. With P0441 the ECU says that, when opening or closing the valve, it didn't see the expected effect on the mixture or the pressure: the flow is too much, too little or none.

Symptoms

  • Often just the light.
  • If the valve stays open: rough idle and hard starting right after refuelling.
  • Sometimes a smell of petrol.
  • With the valve stuck open, P0172 (running rich) can appear too.

Most likely causes, in order

  • The purge valve stuck open or closed.
  • A hose between valve, canister and engine blocked, cracked or disconnected.
  • The charcoal canister saturated or broken, sometimes from a habit of topping up past the pump's click.
  • The valve's connector or wiring.

What to check before the garage

  • Check the fuel cap: closed until it clicks and with the seal intact. It costs nothing and is sometimes enough.
  • Look at the hose from the purge valve to the intake manifold: it should be intact and pushed fully on.
  • Note whether the car struggles to restart right after refuelling: it's the typical clue of a valve stuck open.

At the garage: what to ask for

A test of the purge valve commanded by the tool, which must open and close on command without leaking when shut, and a check of the hoses. The canister gets looked at if the valve is fine.

What DrivePulse shows

DrivePulse reads P0441 and opens its card, with the advice to check the fuel cap anyway. In the live data, on cars that report it, you see how much the ECU is commanding the purge valve; in Health the engine mixture shows whether the mixture goes rich when the valve opens.

The Before the inspection card shows which self-tests are ready, including the vapour test on cars that run it.

Frequently asked questions

Can I drive with P0441?

Yes, normally. It's worth fixing before a stuck-open valve makes the mixture rich and brings other codes.

Why does the car struggle to restart after refuelling?

If the purge valve stays open, right after filling up the engine draws in too much petrol vapour and the mixture becomes too rich to start cleanly.

Is topping up past the click bad?

Yes. Liquid petrol can reach the charcoal canister and ruin it. It's better to stop at the pump's first click.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes