EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Fuel vapour (EVAP)
  4. P0442

P0442: EVAP system small leak detected

If the car reports evaporative system pressure, a small leak shows as a value that returns towards zero too quickly during the test, which only runs with the tank neither nearly empty nor full. Check the fuel cap seal first. You can drive if there is no fuel smell; with a strong smell, do not use the car.

Get DrivePulse

What to look at in live data

In the live data, look for the evaporative system pressure, if the car reports it, and the commanded purge. During the test the ECU closes the vent, creates a slight vacuum in the tank (or slight pressure, depending on the system) and watches whether it holds: with a small leak the value drifts back toward zero too quickly. The test only runs under specific conditions, with the tank neither nearly empty nor full and the engine started cold after a long stop, which is why the code can return days later.

The first check is still the fuel cap: a cracked seal or a cap not turned until it clicks. In the on-board test results (mode 06), if the car reports them, the small leak test gives the measured value and the limit: a result close to the limit after a repair means the job is not finished. Other typical leaks are cracked plastic lines near the canister and a vent valve that does not close.

How serious is it, can you drive?

Severity is low: if you can't smell petrol, you can drive normally. It's worth fixing because the vapour escapes into the air and because with the light on the car may fail its inspection.

Read P0442 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Now and then, with a cold engine and under precise conditions, the ECU seals the system and checks whether it holds pressure or vacuum. If the seal drops more than expected, it works out how big the equivalent hole is.

EVAP codes come in steps: P0456 for a very small leak, P0442 for a small one, P0455 for a large one, like an open cap. P0442 sits in the middle: it's usually not a forgotten cap, but a seal or a hose.

Symptoms

  • Check engine light on, almost always with nothing else.
  • Sometimes a smell of petrol near the car, especially in hot weather.
  • The engine runs normally.

Most likely causes, in order

  • The fuel cap seal, hardened or cracked, or a non-original cap that doesn't seal well.
  • A vapour hose cracked or a loose clamp, often near the tank or the charcoal canister.
  • The canister vent valve not closing fully.
  • The filler neck seal.
  • The charcoal canister cracked or damaged by too many top-ups past the click.

What to check before the garage

  • The cap: open it, check the seal is intact and soft, then close it until it clicks.
  • If the cap is a generic replacement, try an original one: some don't seal properly.
  • When refuelling, stop at the pump's first click without topping up: liquid fuel in the charcoal canister ruins it.
  • If you smell strong petrol, don't use the car and don't smoke near it: get it checked straight away.

How long it takes to clear

The leak test doesn't run on every trip: it usually needs a cold start after a long stop, with the tank neither nearly empty nor full. That's why, after fixing the cap or a hose, the light can stay on for a few days.

If after a week of normal use the code comes back confirmed, the leak is still there and a smoke test is worth it.

At the garage: what to ask for

A smoke test, which shows where the vapour escapes, and commanding the vent and purge valves from the scan tool. In order of cost: cap, clamp or hose, vent valve, filler neck seal, charcoal canister.

What DrivePulse shows

DrivePulse reads P0442 and opens the fuel vapour card, with the warning not to use the car if you smell strong petrol and the advice to stop at the first click when refuelling; it also says whether the code is pending or confirmed.

After the repair, Before the inspection tells you when the EVAP self-test is ready again: until it is, the test hasn't run again and the light may stay on.

Frequently asked questions

Can I drive with P0442?

Yes, if you can't smell petrol: the engine isn't affected. If the smell is strong, don't use the car.

What's the difference from P0456 and P0455?

They report the same kind of leak at different sizes: P0456 very small, P0442 small, P0455 large, like an open cap.

I replaced the cap and the light is still on: is that normal?

Yes, for a few days: the leak test only runs under certain conditions. If after a week the code comes back confirmed, the leak is somewhere else.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes