What to look at in live data
P0222 concerns the second position signal, B, which depending on the car belongs to the throttle or the pedal. In the standard data look for throttle position B and the pedal positions (D and E): with the ignition on and the engine off, signal B should start from a steady value, never zero, and rise smoothly as you press the pedal.
A B signal that stays at or near zero while the other one moves points to a broken wire, a short to ground or a faulty sensor; if it drops to zero only now and then, gently move the connector and watch whether the value jumps. Since sensors A and B often share supply and ground, a reference voltage problem sets codes for both: in that case the fault is in the shared wiring or the ECU, not the sensor.
How serious is it and can you drive?
Severity is high. Drive gently to the garage: in limp mode power is reduced. If the engine accelerates on its own, stop somewhere safe and switch it off.
Read P0222 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Each sensor gets a supply voltage from the control unit, usually 5 volts, and sends back a signal that changes with position. A healthy signal never goes to zero and never reaches the maximum: those values are reserved for faults. With P0222 signal B stayed below the minimum threshold.
On many cars sensor B is in the throttle body, on others it's in the pedal: that's why the official name says throttle/pedal. The garage's diagnostic tool tells you which one your car has.
Symptoms
- Reduced power, limp mode: the car responds poorly to the accelerator.
- Rough idle or revs rising on their own.
- Check engine light on; sometimes the automatic gearbox shifts badly.
- The fault can come and go with vibration or damp.
Most likely causes, in order
- The connector of the throttle body or the pedal, corroded, loose or with water inside.
- A signal wire broken or shorted to ground: a low signal is the typical fault of a wire that has come off or touches the bodywork.
- The sensors' shared supply failing: if P0122, signal A, is there too, the problem is almost always there and not in the sensors.
- The sensor worn internally: in the throttle body, the whole body is usually replaced.
What to check before the garage
- With the engine off, look at the connector on the throttle body and the one above the pedal: fully pushed in, no corrosion, no traces of oil or water.
- Check that the floor mat doesn't touch or block the pedal.
- Think back to recent work in the engine bay, or an engine wash: a wet connector is enough for this code.
Low, high or inconsistent signal
Three different codes tell three different stories. P0222 is signal B too low: usually a wire or a connector. P0223 is the signal too high, often a short to the supply. P2135 says A and B are both within range but don't agree, which points more to a worn sensor.
Knowing this helps you avoid replacing parts at random: with P0222 alone, before buying a throttle body it's worth measuring the wires and the connector.
At the garage: what to ask
Reading both signals with the diagnostic tool while the pedal is pressed slowly, measuring the sensors' supply and ground, and checking the wiring. In order of cost: cleaning or repairing the connector, wiring repair, and only then a new throttle body or pedal.
What DrivePulse shows
DrivePulse reads P0222 and opens the accelerator and throttle sensor card, with the floor mat check, the connector above the pedal and the advice to stop if the engine accelerates on its own; it also tells you whether the code is pending or confirmed.
If P0122, P2135 or P2138 show up too, you see them in the same list: two low-signal codes together point to the shared supply. In live data, on cars that report it, the throttle position read with the engine running and the car standing still shows whether the signal is there or stays at zero.
Frequently asked questions
Can I drive with P0222?
Only gently to the garage, because power is reduced. If the engine accelerates on its own, stop somewhere safe and switch it off.
What's the difference from P2135?
P2135 says the two signals don't agree. P0222 says signal B is too low, almost always because of a wire or a connector.
Does the throttle body need replacing?
Not first. With P0222 alone, fixing the connector or a wire is often enough. The throttle body is replaced when the measurements show it's the sensor.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.