What to look at in live data
With the throttle motor circuit open, the ECU can no longer move the throttle: it stays in its rest position, slightly open, and the car goes into limp mode with limited revs and little response to the pedal. In the standard data it shows clearly: commanded throttle actuator changes when you press the pedal, while absolute throttle position stays fixed at a low value.
The problem is electrical: a corroded or loose throttle body connector, a broken wire between throttle body and ECU, a burnt-out motor. With the engine off, measure the motor resistance across the two connector pins (usually a few ohms) and check that the wires aren't cut where the harness bends. After the repair the throttle needs the learning procedure, which on many cars runs by itself for a few seconds with the ignition on.
How serious is it and can you drive?
Severity is high. The car moves, but without power: joining a fast road or overtaking becomes dangerous. If you have to move it, do so very gently and only for a short distance, away from motorways and dual carriageways, or call roadside assistance.
Read P2100 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The throttle motor is connected to the ECU by two wires. When the ECU drives it, it checks whether current flows in the circuit. If none flows at all, as with a disconnected wire, it stores P2100: circuit open.
With no drive, a spring pulls the throttle into a slightly open rest position designed precisely for faults. The engine keeps running and the car moves, but pressing the accelerator changes little or nothing.
Symptoms
- Check engine light on, sometimes with an engine fault message too.
- Almost no power: revs barely rise even with the pedal floored.
- Idle slightly higher than usual and steady.
- The problem doesn't go away when you switch off and restart, if the circuit really is open.
Most likely causes, in order
- The throttle body connector unplugged, loose or with a terminal pushed out of its seat.
- A broken wire between throttle body and ECU, often where the harness bends or rubs near the engine.
- The motor with an open winding: then the throttle body is replaced.
- A fuse or relay feeding the throttle control, on some cars.
What to check before the garage
- With the engine off, check whether the connector on the throttle body is clipped all the way in. Unplug it and plug it back in, checking that the terminals are straight, with no corrosion.
- Follow the harness near the throttle with your eyes: no wires pulled, crushed or burnt by hot parts.
- If work was recently done in the engine bay, a connector left unplugged is the first suspect.
Open circuit and throttle at rest
That's the difference from the other throttle codes. With P2101 the motor works, but badly; with P0638 the throttle moves but doesn't reach where it should. With P2100 the motor gets no current at all, so the throttle doesn't move.
That's why the cause is almost always electrical and easy to find: a connector, a wire, a terminal. Cleaning the throttle won't help here.
At the garage: what to ask
Checking the connector and wires up to the ECU, measuring the motor's resistance and testing the drive with a diagnostic tool. In order of cost: connector or terminal, wire repair, fuse or relay, a new throttle body with position relearn.
What DrivePulse shows
DrivePulse reads P2100 and opens the throttle body card, with the advice to drive very gently if the car goes into limp mode; it also tells you whether the code is pending or confirmed.
In live data, on cars that report it, you'll find the throttle position. With the car standing still and the engine running, if it stays at the same value when you gently press the pedal, the motor isn't moving it. If P0638 or P2101 show up too, DrivePulse lists them together.
Frequently asked questions
Can I drive with P2100?
Only for a short distance and very gently: the throttle stays at rest and the car has no power for overtaking or joining traffic. If you can, call roadside assistance.
What's the difference from P2101?
P2101 says the throttle motor works badly. P2100 says its circuit is open: no current flows and the throttle stays put.
Does the throttle body need replacing?
Not first. It's often an unplugged connector or a broken wire. The throttle body is replaced if the tests find the motor itself open.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.