EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Accelerator, idle and brake
  4. P0703

P0703: torque converter/brake switch B circuit fault

Above the brake pedal a switch sends the 'I'm braking' signal to several control units. Circuit B usually goes to the automatic gearbox control unit and to the engine ECU as a second confirmation. With P0703 that signal is missing or impossible: the brakes work, but brake lights, cruise control and gearbox can be affected.

Get DrivePulse

What to look at in live data

P0703 concerns the brake switch input used by the automatic transmission module: it unlocks the lever from P and releases the torque converter lock-up when you brake. Its state isn't among the standard OBD2 data; what you notice is a lever that won't come out of P, or an engine that tends to stall as you brake to a stop, because the converter stays locked.

In the standard data, watch engine rpm as you slow to a stop (the person in the passenger seat holds the phone): if it drops too low and the engine nearly stalls before you stop, the transmission didn't see the brake. If the car reports the brake state, compare it with the brake lights: they should change together. Often the culprit is the switch on the pedal or its plastic stop; sometimes it is the wire carrying the signal to the transmission.

How serious is it, can you drive?

Severity is medium. The brakes still brake, but if the brake lights don't come on, whoever is behind you can't tell you're slowing down. Get to the garage soon, keeping more distance and without cruise control. If the lever stays stuck in P, many cars have a manual release described in the handbook.

Read P0703 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Control units don't trust a single brake signal: the switch gives two, A and B, often one that closes and one that opens when you press the pedal. That way a broken wire doesn't go unnoticed.

P0703 says circuit B is faulty: the signal stays the same all the time, is missing altogether or doesn't change when the pedal moves. On many cars the code is set by the gearbox control unit, which uses the brake to release the lever from P and to unlock the torque converter clutch when you stop.

Symptoms

  • Check engine light on, sometimes the gearbox light too.
  • The automatic gear lever won't come out of P even with the brake pressed.
  • Cruise control won't engage, or doesn't drop out when you brake.
  • Brake lights always off or always on.
  • On some automatic cars you feel a jolt when stopping, because the torque converter stays locked too long.

Most likely causes, in order

  • The switch out of position or out of its bracket, often after a knock from a foot or work under the dashboard.
  • The switch connector, loose or corroded.
  • The brake light fuse blown: on many cars it also powers the switch.
  • A brake light bulb blown, on cars that read the signal through that circuit.
  • The switch failed internally, or the wires to the gearbox damaged.

What to check before the garage

  • In the evening, press the brake with the car facing a wall or a shop window: the brake lights must come on at once and go off as soon as you release the pedal.
  • Check the floor mat isn't holding the pedal slightly down.
  • Listen under the dashboard: pressing and releasing the pedal, the switch usually gives a small click.
  • Check the brake light fuse, following the diagram on the fuse box lid or in the handbook.

Why a brake code sits among the gearbox codes

Codes starting with P07 are about the gearbox. P0703 sits there because the automatic gearbox needs to know when you brake: to let you move the lever out of P, to unlock the torque converter clutch before the engine stops and, on some cars, to change down on descents.

That's why, with P0703, the garage starts from the brake switch and not from the gearbox: the gearbox is fine, it's just missing a piece of information.

At the garage: what to ask for

A live reading of the switch's A and B states while the pedal is pressed: both must change, at the same moment. Then adjusting or replacing the switch, which is usually a cheap part. In order of cost: fuse or bulb, adjustment, new switch, wiring repair.

What DrivePulse shows

DrivePulse reads P0703 and opens the brake pedal sensor card, which starts from the brake lights and tells you not to use cruise control until it's fixed; it also says whether the code is pending or confirmed.

If the switch has also caused P0571 or P0504, you see them in the same list: together they almost always point to the same part, not to two different faults.

Frequently asked questions

Can I drive with P0703?

Yes, carefully and as far as the garage: the brakes work, but first check that the brake lights come on.

What's the difference from P0571?

P0571 is about circuit A of the same switch, P0703 about circuit B. The part to check is the same.

My automatic gear lever won't come out of P: is this why?

Very likely: without the brake signal the gearbox doesn't release the lever. Many cars have a manual release, explained in the handbook.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes