EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Accelerator, idle and brake
  4. P0564

P0564: cruise control multi-function input A circuit fault

The cruise control buttons, on the steering wheel or on a stalk, don't have a wire each: they share the same circuit, and the ECU recognises them by the voltage, different for each button. With P0564 it reads a value that matches no button, or that changes for no reason. The engine runs normally.

Get DrivePulse

What to look at in live data

The cruise control buttons have no value among the standard OBD2 data: the ECU reads one signal with several voltage levels, one per button, and P0564 says that signal is out of range. If the car reports the button states through the manufacturer's diagnostics, press each button with the engine off and the ignition on: each should give its own state, and with the buttons released the value should return to rest.

There is no direct sign in the standard data: with P0564 cruise control usually won't engage at all. The most common fault is in the rotary contact behind the steering wheel (the airbag clock spring), which carries the button signals: if the horn or the radio buttons also stop working, that is the suspect. Water or dirt inside the stalk or the buttons sets this code too.

How serious is it, can you drive?

Severity is low: you can drive normally, but don't use cruise control until it's fixed, because it might not respond to the buttons as you expect. It only becomes urgent if the airbag light comes on too.

Read P0564 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Each button (on, set, plus, minus, resume, cancel) puts a different resistance in the circuit, and the ECU works out which one you pressed from the voltage that reaches it. At rest it must read a precise value.

P0564 says the value on circuit A is outside the expected ones: a button seems pressed when it isn't, two seem pressed together, or the signal is missing. To be safe the ECU switches off cruise control and often the speed limiter too, if it uses the same buttons.

Symptoms

  • Cruise control won't switch on, or drops out by itself after a few seconds.
  • The speed limiter doesn't work, on cars that use the same buttons.
  • Check engine light on; on some cars the cruise control symbol flashes as well.
  • Engine and gearbox run normally.

Most likely causes, in order

  • A worn clock spring in the steering wheel: the coil of wires that carries the button signals while the wheel turns.
  • The switch connector, corroded or loose, behind the wheel or under the steering column.
  • A button that stays pressed, sticks or has had a drink spilled on it.
  • The stalk broken or loose, on cars with the controls on the column.
  • A broken wire between the switches and the ECU, or a replacement part that doesn't suit the car.

What to check before the garage

  • With cruise control off, press each button several times and check it springs back by itself.
  • Turn the wheel fully right and fully left and try the horn and the other buttons: if they stop working in certain positions, suspicion falls on the clock spring.
  • If liquid has recently got onto the buttons, let it dry and try again after a few days.
  • Don't take the steering wheel apart: the airbag is inside, and it only comes out at a garage.

The clock spring and the airbag light

The same clock spring carries power to the steering wheel airbag, the horn and the other buttons. When it wears, the track for the controls often goes first, and sometimes the very first sign is P0564.

If the airbag light comes on along with the engine light, it's no longer just a matter of comfort: the steering wheel airbag might not work in a crash. In that case have the car checked soon.

At the garage: what to ask for

A live reading of the switch value while each button is pressed: it shows whether the fault is in a button or in the clock spring. In order of cost: cleaning the connector, button or stalk, wire repair, clock spring, which means removing the airbag.

What DrivePulse shows

DrivePulse reads P0564 and opens the cruise control switch card, with the tests to do on the buttons, the warning not to take the wheel apart and the advice to have it checked soon if the airbag light comes on; it also says whether the code is pending or confirmed.

If brake codes such as P0571 or P0703 show up too, DrivePulse lists them together: cruise control also needs the brake signal, and a fault there keeps it off.

Frequently asked questions

Can I drive with P0564?

Yes: the engine isn't affected. Leave cruise control off until it's fixed.

Why has the speed limiter stopped working too?

On many cars the limiter uses the same buttons as cruise control: if the button circuit can't be trusted, the ECU switches both off.

Does the clock spring have to be replaced?

No: the connector and the buttons are checked first. It's replaced if the live reading shows the fault even with the buttons at rest, or if the airbag light comes on too.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes