What to check before the garage
- Whether P0545 or P0546 shows up too: they tell you whether the signal is low or high and narrow the search.
- With the engine cold, where you can reach it, the sensor connector: dry, clean and pushed fully home.
- The wiring that runs along the exhaust: clips in place and no wire resting on hot parts.
- On diesels, whether the DPF light comes on: it means the filter is filling up and the fault needs fixing soon.
What to look at in live data
P0544 concerns the circuit of the exhaust gas temperature sensor ahead of the turbo or the filter, depending on the engine. If the car reports exhaust gas temperature, the most useful check is done with the engine cold: after a night parked the sensor should read roughly the outside air temperature. With the engine running the value should rise smoothly with load and fall when you lift off, which on the move is for the person in the passenger seat to watch.
A value that jumps by hundreds of degrees in an instant, or stays still while load changes, points to the circuit: a cooked connector, a wire broken near the exhaust, a sensor with a broken element. On diesels the ECU uses this temperature to protect the turbo and the particulate filter: with the sensor ignored it may limit power or give up on regenerations, so it is worth fixing soon.
How serious is it, can you drive?
Severity is medium. It isn't an emergency: you can drive gently. On diesels, though, the ECU may suspend DPF cleaning for as long as the fault remains, so putting it off for a long time costs more than fixing a sensor.
Read P0544 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Sensor 1 is the one closest to the engine: on diesels usually before the turbo or the catalytic converter, on some petrol engines near the manifold. It measures very high temperatures, and the ECU uses them to protect the turbo and converter and, where there's a DPF, to manage the cleaning of the filter.
With P0544 the ECU only says the circuit has a problem, without saying whether the signal is low or high. When it knows, it sets P0545 for a low signal or P0546 for a high one.
Symptoms
- Engine light on, often with no other signs.
- On diesels, DPF cleaning being put off, and over time the filter light.
- In some cases the engine limited to protect the turbo.
Most likely causes, in order
- The sensor connector corroded, often fitted in a hot, dirty spot.
- Wiring baked by the heat of the exhaust, with cracked or melted sleeving.
- A failed sensor, worn out by extreme temperatures.
- Moisture in the connector, after an engine wash or heavy rain.
At the garage: what to ask for
A check of the value the sensor reads with a cold engine, which should be close to the outside temperature, a continuity test of the wiring and a check of the connector. If needed, a new sensor and then a DPF clean. In order of cost: connector and wiring, sensor, filter cleaning if it has filled up.
What DrivePulse shows
DrivePulse reads P0544 and opens its card, with the warning that the ECU may suspend DPF regenerations until it's fixed; it also tells you whether the code is pending or confirmed and lists P0545 or P0546 alongside it if they're there.
On suitable cars the DPF status shows the regenerations and the km to the next one: if the next one keeps slipping, the sensor needs fixing soon.
Frequently asked questions
Can I drive with P0544?
Yes, gently: it isn't an emergency. On diesels don't put it off too long, because DPF cleaning may stay suspended.
What's the difference from P0545 and P0546?
They're the same family. P0544 says the circuit has a problem; P0545 and P0546 specify whether the signal is low or high.
Where is sensor 1?
It's the one closest to the engine: on diesels usually before the turbo or the converter. The handbook or the garage will show you the exact spot.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.