EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Exhaust, catalytic converter and DPF
  4. P244C

P244C: exhaust temperature too low for particulate filter regeneration, bank 1

To burn off the soot it collects, the DPF has to get very hot. With P244C the ECU tried to regenerate it, but the exhaust temperature stayed below what's needed.

Get DrivePulse

What to look at in live data

To regenerate the particulate filter the ECU must bring exhaust gas above roughly 550 to 600 °C, and P244C says it can't. If the car reports exhaust or filter temperatures, watch them during a regeneration on an open road, with the phone in the hands of the person in the passenger seat: they should rise within a few minutes and stay high; with P244C they rise little or fall back.

The most common causes lie before the filter: an oxidation catalyst that no longer works (the heat is created there, burning the fuel injected after combustion), a thermostat stuck open that keeps the engine cold (watch coolant temperature, which should sit around 90 °C), temperature sensors that read low, or trips that are too short and slow. An exhaust air leak ahead of the sensors also lowers the temperatures they read.

How serious is it, can you drive?

Severity is medium. You can drive gently, but don't leave the code there: a DPF that can't regenerate fills up, and then come limp mode and a bigger clean at the garage.

Read P244C on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The diesel particulate filter collects soot and burns it off from time to time: that's a regeneration. To do it the ECU raises the exhaust temperature, partly with an extra shot of diesel that the oxidation catalyst turns into heat.

Exhaust gas temperature sensors check the heat really arrives. With P244C the temperature stayed too low: the regeneration failed and the soot remains in the filter.

Symptoms

  • Engine light on, sometimes with the DPF light.
  • Regenerations that happen often or never finish.
  • Over time, reduced power as the filter fills up.
  • It may come with P2463 (too much soot in the DPF) or P2002.

Most likely causes, in order

  • Lots of short trips: the exhaust never gets up to temperature and every regeneration is cut short. The most common cause.
  • An aged oxidation catalyst: it no longer turns the diesel into heat, so the temperature doesn't rise.
  • An exhaust gas temperature sensor drifting and reading lower than the real value.
  • A thermostat stuck open: the engine stays cold and the exhaust does too.

What to check before the garage

  • Do an out-of-town drive of at least 20 minutes at steady speed, in a gear that keeps the revs up a little: the regeneration often completes.
  • Watch the coolant temperature with a warm engine: if it stays low even after a good run, suspect the thermostat.
  • Avoid switching off in the middle of a regeneration, if the car tells you one is running.

At the garage: what to ask for

A comparison of the temperatures read by the exhaust sensors with those expected during a regeneration, a thermostat check and, if needed, a forced regeneration with the diagnostic tool. If the oxidation catalyst no longer heats up, it has to be replaced.

What DrivePulse shows

DrivePulse reads P244C and its card suggests an out-of-town drive of at least 20 minutes at steady speed, and suspecting the thermostat if the engine stays cool; it also tells you whether the code is pending or confirmed.

On suitable cars the DPF status shows the regenerations and the km to the next one, and DrivePulse warns you when a regeneration is interrupted halfway. Live coolant temperature helps tell whether the thermostat is doing its job.

Frequently asked questions

Can I drive with P244C?

Yes, gently. But don't put it off: a DPF that can't regenerate clogs up.

Is a motorway run enough?

It often helps: 20 minutes or more at steady speed lets the regeneration finish. If the code comes back, there's a fault to find.

Does the DPF need replacing?

Usually not. The problem is heat not arriving: trips, thermostat, sensors or the oxidation catalyst.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes