EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Exhaust, catalytic converter and DPF
  4. P2002

P2002: diesel particulate filter efficiency below threshold

The pressure across the DPF doesn't match what the ECU expects. In most cases the filter is too loaded with soot, and the right drive can still sort it out.

Get DrivePulse

What to do straight away

  • Take a drive of at least 30 minutes at steady revs, around 2,000 to 2,500 rpm, on a main road or motorway. It's often enough for a complete regeneration.
  • If the light stays on, go to a garage for a forced regeneration before the filter clogs completely. After that it would need cleaning or replacing, which costs far more.
  • Don't clear the code and then ignore it: meanwhile the filter keeps filling up.

What to look at in live data

The value to watch is the differential pressure across the diesel particulate filter, if the car reports it: the difference in pressure between the filter inlet and outlet. With P2002 the ECU sees a smaller difference than it expects for that exhaust flow.

At idle the value is low; under acceleration, with the phone in the hands of the person in the passenger seat, it should rise steadily. If it stays close to zero even under load, the filter may be cracked or emptied, but check the two sensor pipes first: loose, holed or full of condensation, they set the same code and cost far less than the filter.

Read P2002 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

P2002 means diesel particulate filter, efficiency below threshold, bank 1. The filter has a differential pressure sensor that measures the difference between its inlet and outlet. The ECU compares it with what it expects at those revs and that load. If the values don't add up, it stores P2002.

In most cases the filter is too loaded with soot. Less often it's damaged, or the sensor is measuring wrong.

Most likely causes

  • A filter clogged by too many short trips.
  • Regenerations always interrupted, because the engine gets switched off before they finish.
  • A drifting differential pressure sensor.
  • A filter at the end of its life, usually beyond about 180,000 km.

Symptoms

The DPF light, the check engine light or both come on. The car can lose power and go into limp mode, fuel consumption rises and the radiator fan runs more often, a sign of constant regenerations.

How to avoid it

The DPF dislikes short trips. If you use the car almost only in town, a 20 to 30 minute drive with a warm engine now and then lets regenerations finish. Use oil with the specification for cars with a particulate filter, and don't switch off when you notice a regeneration is in progress.

When to see a mechanic

  • The light stays on after the long drive.
  • The car is in limp mode.
  • The code comes back a few days after a regeneration at the garage, which points to the sensor or a filter at the end of its life.

What DrivePulse shows

The P2002 card in DrivePulse first asks you to open DPF status in Health and look at how many regenerations were interrupted. There you find the last regeneration, the history of completed ones and those where the signal was lost, how loaded the filter is compared with your trips and, on cars that expose it, the soot measured by the ECU.

When the filter is cleaning you see it live on the Dashboard, in the pill at the top of the iPhone and on CarPlay, with a reminder not to switch off.

Frequently asked questions

Does clearing the code fix it?

No. The filter stays loaded, and the code returns as soon as the ECU runs its check again. Meanwhile the filter keeps filling, and a forced regeneration can turn into cleaning or replacement.

How is the differential pressure sensor checked?

At a garage they compare the readings with the engine off and at idle. With the engine off the pressure difference should be close to zero. If it isn't, the sensor or its hoses need checking before blaming the filter.

Can I drive with P2002?

Yes, carefully, to do the drive that lets it regenerate or to reach a garage. If the car loses a lot of power or goes into limp mode, go to a garage without waiting.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes