EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Exhaust, catalytic converter and DPF
  4. P2000

P2000: NOx trap efficiency below threshold, bank 1

If the car reports the NOx sensor after the catalyst, with the engine warm it should read low between purges; if it rises again straight away, the catalyst stores little. Check exhaust gas temperature too: it works best between about 250 and 450 °C. You can drive gently, but the roadworthiness test is at risk.

Get DrivePulse

What to look at in live data

The NOx storage catalyst holds nitrogen oxides, and every so often the ECU empties it with short rich phases. If the car reports the NOx sensor after the catalyst, with the engine warm it should read low between one purge and the next; if the value climbs again right after every purge, the catalyst is storing little.

Check exhaust gas temperature too, if available: this catalyst works best roughly between 250 and 450 °C, and lots of short trips never get it there. If the temperature is right and the NOx sensor after the catalyst stays high, suspect the catalyst or the sensor itself, which a garage compares with the one before it.

How serious is it, can you drive?

Severity is medium. You can drive normally and gently, but nitrogen oxide emissions rise and with the light on the inspection test is at risk. It's not a fault to ignore for months: a sensor that misreads can also upset how regenerations are managed.

Read P2000 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

A NOx storage catalyst works like a sponge: it holds nitrogen oxides while the engine runs lean, then the ECU briefly enriches the mixture and turns them into harmless gases. This clean-out is called a regeneration.

A NOx sensor before and one after the catalyst measure how much goes in and how much comes out. With P2000 the difference is too small: the catalyst is trapping less than expected, or one of the sensors is reading wrongly.

Symptoms

  • Often just the engine light: nothing is noticeable while driving.
  • Sometimes slightly higher fuel use, from more frequent regenerations.
  • Rarely reduced power, on some models.
  • It may appear with NOx sensor or catalyst codes.

Most likely causes, in order

  • An aged catalyst or one poisoned by sulphur, which builds up over time and makes it less effective.
  • The NOx sensor after the catalyst drifting: it misreads and makes the catalyst look worse than it is.
  • An exhaust leak before the sensor, which skews the measurement.
  • Lots of short trips: the exhaust never gets hot enough and the regenerations don't complete.

What to check before the garage

  • Think about how you use the car: if it's almost all short trips, a long drive at steady speed can let the catalyst clean itself.
  • Listen to the exhaust from cold: a ticking or puffing near the manifold can mean a leak.
  • Check that the fuel and oil meet the specification the manufacturer requires: sulphur ruins this catalyst.

At the garage: what to ask for

A reading of both NOx sensors during a regeneration, to see whether the catalyst is working or a sensor is wrong, and a check for exhaust leaks. The catalyst is replaced last, once the sensors and leaks have been ruled out.

What DrivePulse shows

DrivePulse reads P2000 and its card suggests a long drive at steady speed first, then at the garage the NOx sensor and exhaust leaks, with the catalyst last; it also tells you whether the code is pending or confirmed.

If after a few long drives the code stays pending and never confirms, that's a good sign: the regenerations are doing their job.

Frequently asked questions

Can I drive with P2000?

Yes, gently: it usually gives no symptoms while driving. But emissions rise and the inspection test is at risk, so it needs fixing.

Does the catalyst need replacing?

Not first. The NOx sensors and exhaust leaks are checked first; the catalyst is only replaced if it's really worn out.

Is it the same as AdBlue?

No. P2000 is about the catalyst that traps nitrogen oxides. The AdBlue system reduces them in a different way and has its own codes, such as P20EE.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes