What to look at in live data
The SCR catalyst reduces nitrogen oxides using AdBlue. If the car reports the NOx sensors, compare the one before the catalyst with the one after: with the engine warm and the exhaust above about 200 °C, the one after should read far less than the one before. If they read nearly the same, the reduction is not happening.
The most common causes are poor quality or old AdBlue, an AdBlue injector clogged with crystals and a NOx sensor that reads wrong. If the car also shows AdBlue level and quality, check those before suspecting the catalyst.
How serious is it and can you drive?
Severity is medium, but with a deadline. Usually the car drives normally, but emissions are out of limits and, if the countdown appears, the engine won't restart when it reaches zero. Don't wait for the last mile: take the car to a garage while it still starts.
Read P20EE on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The SCR catalyst reduces the nitrogen oxides, NOx, from a diesel. To do it an injector sprays AdBlue into the exhaust, a solution of urea and water kept in a separate tank. Two NOx sensors, before and after the catalyst, measure how much work it does. With P20EE the ECU says too much NOx remains after the catalyst compared with what should remain.
Symptoms
- Check engine or AdBlue warning light on.
- Dashboard messages about AdBlue or emissions.
- On many cars, a mileage countdown: at zero the engine won't restart until the problem is fixed.
- Often no change in how the car drives.
Most likely causes, in order
- Poor-quality AdBlue, diluted, old or contaminated, or a nearly empty tank.
- The AdBlue injector crusted with crystals, or the pump not building pressure.
- A NOx sensor measuring wrong.
- The SCR catalyst aged or damaged.
- An exhaust leak skewing the measurements.
What to check before the garage
- The AdBlue level. If it's low, top up with AdBlue meeting ISO 22241, from a sealed container or a pump.
- If you recently topped up with a doubtful product or a container left open for a long time, tell the garage.
- See whether the dashboard shows a mileage countdown: it decides how much time you have.
At the garage: what to ask for
A check of AdBlue quality with a refractometer, a flow test of the injector and pump, and a comparison of the two NOx sensors. The SCR catalyst is only replaced after ruling everything else out.
What DrivePulse shows
DrivePulse reads P20EE and opens its card, with the advice to start from AdBlue level and quality. It tells you whether the code is pending or confirmed and, on many cars, how far you have driven with the light on, useful for knowing how long the problem has been there.
On diesels, DPF status in Health helps you keep an eye on the other big exhaust system too, the particulate filter.
Frequently asked questions
Can I drive with P20EE?
Usually yes, but if the dashboard shows a mileage countdown, the engine won't restart at zero. Get to a garage before then.
Can topping up AdBlue fix it?
Yes, if the tank was nearly empty or the AdBlue was poor quality. After topping up, the code can take a few drives to disappear.
Can I use water instead of AdBlue?
No. Water doesn't reduce NOx, damages the system and still triggers the warnings. You need AdBlue meeting ISO 22241.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.