EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Diesel: glow plugs, AdBlue and intake manifold
  4. P20E8

P20E8: reductant (AdBlue) pressure too low

The AdBlue pump can't pressurise the fluid that goes to the injector in the exhaust. Without pressure the system can't cut nitrogen oxides, and the countdown starts.

Get DrivePulse

What to look at in live data

AdBlue pressure is not among the standard OBD2 data: many recent cars report reductant system data such as tank level and system status, and some report pressure through the manufacturer's diagnostics. If you can see it, with the engine running and warm it should rise to a few bar (often between 5 and 9, depending on the system) a few seconds after the pump starts and stay steady; with P20E8 it doesn't get there or drops while dosing.

Check the AdBlue tank level and the outside temperature: with the tank nearly empty the pump draws in air, and below about -11 °C AdBlue turns solid, so pressure only builds once the heaters have thawed it. If the level is right and the weather is warm, the suspects are a pump filter clogged with crystals, a leak in the line to the injector (white crystals along the route) or the pump itself.

How serious is it and can you drive?

Severity is medium, with a deadline. The engine works, but emissions are out of limits and, if the countdown appears, the engine won't restart at zero. Take the car to a garage while it still starts.

Read P20E8 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

On diesels with an SCR system a pump draws AdBlue from its tank and sends it under pressure to an injector in the exhaust. A sensor measures the pressure, and the ECU checks it reaches the expected value. With P20E8 it says the pressure stays too low: AdBlue isn't reaching the injector, or is reaching it badly.

Symptoms

  • Check engine or AdBlue warning light on.
  • A fault message about the AdBlue system or emissions.
  • On many cars, a mileage countdown: at zero the engine won't restart.
  • Usually the car drives normally.

Most likely causes, in order

  • AdBlue crystals in the lines or the pump, often after a long period parked or with old AdBlue.
  • Cold: AdBlue freezes at around minus 11 °C; the system has heaters, but if one fails the fluid stays frozen.
  • A clogged pump filter.
  • A pump that's failing.
  • A nearly empty tank or poor-quality AdBlue.

What to check before the garage

  • The AdBlue level. Top up with fresh AdBlue meeting ISO 22241.
  • In very cold weather, try leaving the car somewhere warmer and restarting once the system has warmed up: if the code goes, look at the heaters.
  • Note whether the dashboard shows a mileage countdown.

At the garage: what to ask for

A reading of AdBlue pressure with the tool, a check of the pump filter and the heaters, and clearing crystals from the lines. The pump gets replaced if everything else is fine.

What DrivePulse shows

DrivePulse reads P20E8 and opens its card, which suggests starting with a top-up of fresh AdBlue. It tells you whether the code is pending or confirmed and, on many cars, how far you have driven with the light on.

In Health, battery voltage helps here too: the AdBlue pump and heaters draw current, and a weak battery in winter makes things worse.

Frequently asked questions

Can I drive with P20E8?

Usually yes, but if a mileage countdown appears, the engine won't restart at zero. Get to a garage before then.

Can AdBlue freeze?

Yes, at around minus 11 °C. Cars have heaters to thaw it; if one fails, pressure codes like P20E8 appear in winter.

What's the difference from P20EE?

P20E8 says AdBlue pressure is missing. P20EE says the SCR catalyst isn't cutting enough nitrogen oxides, and low pressure can be one of the causes.

Can the crystals be removed?

Often, yes. At the garage they dissolve them with warm water in the lines and injector, then top up with fresh AdBlue. If the crystals have damaged the pump, the pump needs replacing.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes