What to look at in live data
If the car reports intake manifold flap position, compare the position the ECU asks for with the one the sensor reads. The ECU moves the flaps at certain moments, for example at start-up, at switch-off or above a certain engine speed: at those moments the measured position should follow the requested one without jumps.
On many engines the sensor sits inside the actuator, so a value stuck at one end, near 0 or 100%, points to an electrical fault. A value that moves but never reaches its target points to flaps held back by carbon deposits or a disconnected linkage.
How serious is it and can you drive?
Severity is medium. You can drive gently. On some engines the flaps are held by small screws, and if a flap comes loose it can end up in the engine: if your engine is known for this or you hear new noises from the intake, have it checked soon.
Read P2015 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Many engines, especially diesels, have flaps in the intake manifold, called swirl flaps or runner flaps, that close part of the passages at low revs to make the air swirl: combustion improves and less soot forms. An actuator moves them all together through a linkage, and a sensor reads their position. With P2015 the ECU says the position it reads doesn't match the one it commanded.
Symptoms
- Often just the light.
- A slight lack of pull at low revs.
- A slightly less steady idle.
- More rarely, limp mode.
Most likely causes, in order
- Carbon in the manifold: EGR gases and oil vapour form deposits that jam the flaps. It's the classic case on many diesels, including those from the Volkswagen group.
- The actuator linkage, worn or with a broken plastic joint.
- The actuator, electric or vacuum, failed, or a vacuum line off.
- The position sensor or its connector.
What to check before the garage
- If you can see the actuator on the manifold, check with the engine off that the linkage is intact and connected.
- Look for loose or cracked vacuum lines near the actuator, if it's that type.
- Read all the codes: if there are EGR codes too, the manifold is probably coked up.
At the garage: what to ask for
An actuator test commanded by the tool, watching whether the linkage moves through its full travel. If the linkage is broken, inexpensive repair kits exist for many engines. If the flaps are jammed by carbon, the manifold needs cleaning, often together with the EGR.
What DrivePulse shows
DrivePulse reads P2015 and opens its card with causes and checks. It also shows the other intake and EGR codes, which help you tell whether carbon is the problem.
Statistics show how much time the car spends with a cold engine and on short trips: the conditions in which the manifold and EGR get dirtiest.
Frequently asked questions
Can I drive with P2015?
Yes, gently. If your engine is known for flaps coming loose or you hear new noises, have it checked soon.
Does the manifold need replacing?
Not always. Repairing the linkage or cleaning the carbon out is often enough. It's replaced if the flaps or their spindles are damaged.
Why does the manifold get dirty?
Because EGR gases and crankcase oil vapour pass through it: together they form deposits, especially with short trips and a cold engine.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.