What to look at in live data
The position of the intake manifold runner flaps (the valves that change the air path in the intake) is not among the standard OBD2 data, and P2008 is an electrical fault: the ECU drives the actuator and finds the circuit open. If the car reports the flap position through the manufacturer's diagnostics, it should change with the ignition on when the actuator is commanded; if it stays still, the command isn't getting through.
The check that counts is done with the engine off: an actuator connector that is loose or has green pins, wires broken where the harness runs over the engine, an open actuator. On engines with a vacuum actuator, the ECU drives a solenoid valve and the code is about that valve and its wires. In the standard data the signs are only indirect: less pull at low revs and a slightly uneven idle, which on their own don't tell you where the fault is.
How serious is it and can you drive?
Severity is medium: you can drive gently, the engine performs less well but isn't harmed right away. Don't wait too long: if you hear a ticking or a new noise from the manifold, get it checked soon, because in rare cases a broken flap can come loose.
Read P2008 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The manifold flaps help the air swirl into the cylinders at low revs and fill them better at high revs. The ECU opens and closes them depending on engine speed, through an electric motor or a solenoid valve that sends vacuum to a diaphragm.
With P2008 the ECU sends the command but finds no continuity in the circuit: a broken wire, an unplugged connector or an open actuator winding. Unlike P2015, which is about the flaps' measured position, here the problem is on the control wire.
Symptoms
- Check engine light on.
- Less pull at low or high revs, depending on where the flaps stopped.
- Slightly rough idle on some cars.
- Often no other obvious trouble.
Most likely causes, in order
- The actuator connector corroded, loose or unplugged: it sits on the manifold, in the heat and near oil.
- The wiring near the manifold broken or burnt.
- The actuator motor with an open winding.
- The vacuum solenoid valve, on cars that use one, failed or with its connector unplugged.
What to check before the garage
- With the engine off, find the actuator on the manifold: check the connector is fully latched with no green on the contacts.
- Follow the actuator wiring: no squashed or melted sections.
- If the car has a vacuum solenoid valve, look at its connector and small hoses too.
- Think about any recent work near the manifold: a connector left unplugged is the simplest cause.
If the problem returns after the repair
If the actuator was replaced and the code comes back, ask whether the calibration was done: on many cars the new actuator has to be taught to the ECU.
It's also worth having the flaps checked: if carbon deposits jam them, the actuator struggles and fails again.
At the garage: what to ask
A continuity test of the circuit and a check of the actuator's resistance, then commanding the flaps with the diagnostic tool. In order of cost: connector, wiring repair, vacuum solenoid valve, new actuator with calibration, and the manifold only if the flaps are broken.
What DrivePulse shows
DrivePulse reads P2008 and opens the manifold flaps card, with causes, checks and the advice to get it looked at soon if you hear new noises; it also tells you whether the code is pending or confirmed.
It also shows the other intake and EGR codes, such as P2015 or P0401: if they appear together, they help tell whether carbon-jammed flaps are involved besides the circuit.
Frequently asked questions
Can I drive with P2008?
Yes, gently: the engine performs less well but isn't harmed right away. If you hear new noises from the manifold, get it checked soon.
What's the difference from P2015?
P2015 is about the flaps' position as read by the sensor. P2008 is about the circuit that drives them, so usually a connector, a wire or the actuator.
Does the whole manifold need replacing?
Usually not: the fault is often in the connector, the wiring or the actuator. The manifold is only replaced if the flaps are broken.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.