What to look at in live data
The glow plug module is the control unit, or smart relay, that powers all the glow plugs; P0670 says the circuit the engine ECU uses to command it isn't working. Glow plugs have no value in the standard data, but a module that doesn't switch them on shows on a cold start: watch engine rpm in the first seconds after a cold night, rising slowly and unevenly, with lots of white smoke.
Unlike a single failed glow plug, here they all heat little or not at all: a few degrees above zero the engine starts almost normally, below zero it struggles or won't start. The check is done with the engine cold: the module's power fuse (often a large fuse in the engine bay), the module connector and the control wire. Watch the control module voltage during preheating too: if it doesn't dip even slightly, the glow plugs aren't drawing current.
How serious is it, can you drive?
Severity is medium. Once started, the engine runs normally and you can drive gently. The risk is being stranded on a cold morning, and hard starts strain the battery and the starter. It's best to plan the repair before winter.
Read P0670 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
A diesel engine has no spark plugs: the fuel ignites from compression. When cold that isn't enough, so the glow plugs heat the cylinders for a few seconds before and after starting. They draw a lot of current, so the ECU doesn't power them directly: it drives a module, or glow plug control unit, which feeds them all.
With P0670 the ECU sees a fault in the circuit of this module: the command doesn't get through, the module doesn't respond as it should, or the module itself has failed.
Symptoms
- Long or difficult cold starts, especially in winter.
- White or grey smoke and a rough engine for the first seconds after starting.
- The glow plug light flashing or staying on, on some cars.
- Usually no symptoms once the engine is warm.
Most likely causes, in order
- The glow plug module failed: with age, the most common case.
- The power fuse or wiring that feeds the module.
- A shorted glow plug, which overloads the module and kills it.
- A corroded module connector, as the module often sits near the engine, among water and heat.
What to check before the garage
- How the engine starts cold in the morning: if it takes longer than usual, write it down.
- The battery: a weak battery makes cold starts much worse and can muddle the diagnosis.
- If you can reach it, the module connector: corrosion or water are a clue.
At the garage: what to ask for
A test of the module and, at the same time, of the glow plugs: if one plug is shorted and only the module is replaced, the new module can fail again. Then a check of the fuse, wiring and connector.
What DrivePulse shows
DrivePulse reads P0670 and its card warns that hard cold starts are coming and advises having the module and plugs tested together; it also tells you whether the code is pending or confirmed. It's a common fault with age on many diesels, for example dCi, HDi and Multijet.
If P0380 or P0683 show up too, DrivePulse lists them together: P0670 is about the module control, P0380 the glow plugs, P0683 the communication between module and ECU.
Frequently asked questions
Can I drive with P0670?
Yes, gently: once the engine is running nothing changes. The risk is not being able to start when cold, so don't put it off too long.
Is replacing the module enough?
Not always. If a glow plug is shorted, the new module can fail again: test them together.
What's the difference from P0380?
P0380 says there is a problem in the glow plug circuit. P0670 says the problem is in the control of the module that powers them.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.