What to look at in live data
Glow plugs have no value among the standard OBD2 data, but their work shows on a cold start. Watch engine rpm in the first seconds after a cold night: with a cylinder 3 glow plug that doesn't heat, the engine starts more slowly, runs unevenly for a moment and makes more white smoke until it warms up. In the on-board test results (mode 06), if the car reports them, cold misfires gather on that cylinder.
The real check is electrical, with the engine cold and off: disconnect the wire from the cylinder 3 glow plug and measure its resistance, which should be low, usually under about 2 ohms; an open plug reads infinite. Check the control module voltage during preheating too: with a weak battery every glow plug heats less. Before unscrewing it, read the section on removal: a seized glow plug that snaps in the cylinder head costs far more than the part.
How serious is it, can you drive?
Severity is low and you can drive gently: once the engine is warm, glow plugs aren't needed. But don't leave it until winter: in the cold, starts take longer, the battery works harder and there's more smoke. On many recent diesels the glow plugs also stay on for the first minutes after starting, to cut smoke and noise.
Read P0673 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The glow plug control module powers one glow plug per cylinder and checks the current each one draws. If the current for the cylinder 3 plug is missing or outside the expected values, it logs P0673.
The code is about the circuit: the plug itself, its connector and the wire to the glow plug control module. It doesn't mean the engine has a mechanical fault.
Symptoms
- Longer cranking when it's cold.
- Engine running rough for the first few seconds after starting.
- White or bluish smoke from the exhaust right after starting.
- Check engine light or glow plug light on or flashing.
- In mild weather, sometimes no symptoms at all.
Most likely causes, in order
- A burnt-out cylinder 3 glow plug, by far the most common cause.
- The glow plug connector, loose, corroded or off.
- The wire between the plug and the glow plug control module, damaged by heat.
- The glow plug control module, if the fault is on its cylinder 3 output.
What to check before the garage
- The connector on the cylinder 3 glow plug: with the engine cold, check it's fully seated and clean.
- With a multimeter, the resistance between the plug terminal and engine ground: a good plug reads very low, a few ohms at most; a burnt-out one reads open circuit.
- If the glow plugs have high mileage, consider replacing them all together: they're the same age and the others often follow soon.
Careful when removing it
Glow plugs sit in the cylinder head for years, through heat and carbon, and can seize. Forced out cold, the tip can snap inside the head, and then extraction becomes a long job that costs far more than the plug.
That's why it's better to remove it with the engine warm, at the right torque and, if needed, with penetrating oil left to soak. If the plug won't budge, stop and take it to a garage equipped for extractions.
At the garage: what to ask for
Reading the glow plug control module's codes, measuring each plug's resistance and testing the connector. In order of cost: connector, one glow plug, all the glow plugs, glow plug control module; extracting a snapped plug is extra.
What DrivePulse shows
DrivePulse reads P0673 and opens its card, which points to the glow plug circuit checks; it also says whether the code is pending or confirmed.
In Health the cranking test records the battery voltage drop at every start: comparing a cold morning before and after the repair shows whether the starter is working less. In Statistics, the time you spend with a cold engine tells you how much a good cold start matters to you.
Frequently asked questions
Can I drive with P0673?
Yes, gently: once the engine is warm, glow plugs aren't needed. But it's worth fixing before winter.
Is replacing the cylinder 3 glow plug enough?
Yes, if the rest of the circuit is fine. With high mileage, many people prefer to replace them all together.
What's the difference from P0380 and P0670?
P0380 covers the glow plug circuit in general, P0670 the module that controls them. P0673 points only to the cylinder 3 glow plug circuit.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.