EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Diesel: glow plugs, AdBlue and intake manifold
  4. P0683

P0683: glow plug control module to engine ECU communication circuit

On diesels a small control module switches on the glow plugs that heat the cylinders before starting. With P0683 the engine ECU has lost its link with that module.

Get DrivePulse

What to look at in live data

The code is about the conversation between the engine ECU and the glow plug module, so the useful data is the module's, if the car reports it: the command the ECU sends and the status the module returns. If the command goes out but the status does not change, or the module does not answer at all, the fault is in the module or the wire between them.

Watch the voltage too as you turn the key and during cranking: a battery that sags below about 10 V can interrupt that conversation. If the voltage holds and the code only appears with a cold engine, the battery is not the cause: suspicion goes back to the module or its connector, which is exposed to moisture and dirt.

How serious is it, can you drive?

Severity is medium. Once started, the engine runs normally, so you can drive gently. The real risk is being stuck on a cold morning, plus a few rough minutes after every cold start. Best fixed before winter.

Read P0683 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Glow plugs heat the diesel's combustion chamber so the engine starts even in the cold. The engine ECU doesn't drive them directly: a dedicated module does, receiving commands and reporting back the state of the plugs.

With P0683 that conversation has broken down or is full of errors. The engine ECU no longer knows whether the glow plugs are coming on, and the module may not receive the command to switch them on.

Symptoms

  • Engine light on, sometimes with the glow plug light flashing.
  • Long or difficult starting in the cold, normal in warm weather.
  • White smoke and a rough engine for the first few minutes after starting.
  • Often no symptoms in summer: the problem shows up with the first cold mornings.

Most likely causes, in order

  • A failed glow plug control module, often after one or more glow plugs shorted and overloaded it.
  • An oxidised connector or a broken signal wire between the two control units.
  • The fuse or ground of the glow plug module.
  • A shorted glow plug tripping the module's protection.

What to check before the garage

  • The glow plug fuse, shown in the owner's manual: the simplest check.
  • The battery condition: with a weak battery cold starting gets worse anyway, which muddies the picture.
  • Note how the car starts early in the morning and after a stop: knowing whether the problem is only from cold helps the garage a lot.

At the garage: what to ask for

A test of every glow plug, one by one, together with the module and the wiring. If the module has burnt out, it must be replaced together with any shorted glow plugs: otherwise the new one fails again for the same reason.

What DrivePulse shows

DrivePulse reads P0683 and its card advises having it checked before winter, testing the glow plugs at the same time; it also tells you whether the code is pending or confirmed.

In Health, the resting battery voltage and the cranking test help separate the two problems: if the battery is healthy and cold starts are slow, suspicion falls on the glow plugs.

Frequently asked questions

Can I drive with P0683?

Yes, gently: once started the engine runs. The risk is not being able to start when it's cold.

Do all the glow plugs need replacing?

Not necessarily. They are tested one by one and the shorted or open ones are replaced; if the module has burnt out, any shorted plugs must be changed with it.

What's the difference from P0380?

P0380 is about the glow plug circuit. P0683 is about the link between the glow plug module and the engine ECU. They often appear together.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes