What to check before the garage
- The NOx sensor fuse, shown in the owner's manual.
- If a km countdown appears on the dashboard, note it and get the car to a garage before it reaches zero.
- Check the AdBlue level and whether there are other warnings: they help tell whether the problem is only the sensor.
What to look at in live data
NOx sensor B is usually the one after the SCR catalyst: it tells the ECU how much nitrogen oxide is left after the AdBlue, and it talks to the ECU through its own small control unit, fitted on its cable. On cars that report them, the standard data includes NOx sensor values: if sensor B is missing entirely, or stays on a substitute value while sensor A moves, communication with it is lost.
The sensor needs a few minutes with a warm engine before it gives real values, so watch it after a stretch of driving, read by the person in the passenger seat. If it never appears, check the fuse and the connector of its control unit, often under the car and full of dirt, and the cable along the exhaust. Without this sensor the ECU can't monitor the AdBlue system, and on many cars the countdown of kilometres before the engine won't restart begins.
How serious is it, can you drive?
Severity is medium, but it shouldn't be put off. On diesels with AdBlue, a fault in the SCR system can start a countdown in km: when it reaches zero, the engine won't restart until the fault is fixed. Drive to the garage without waiting.
Read U029E on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
A NOx sensor doesn't send a simple electrical signal: it has its own small control unit that measures nitrogen oxides and sends the data over the CAN network. The engine ECU uses them to dose AdBlue and to check the SCR catalyst is working.
Codes starting with U are communication faults. With U029E the messages from NOx sensor B no longer arrive: the problem may be the sensor, its power supply or the wiring that links it to the network.
Symptoms
- Engine light on, often with an AdBlue system warning on the dashboard.
- On many diesels a message showing the km left before the engine will no longer restart.
- Sometimes reduced power.
- It may appear with other SCR codes, such as P20EE.
Most likely causes, in order
- The sensor wiring or connector, which runs under the car and is exposed to heat, water and dirt: many technical bulletins name it as the most frequent cause.
- A failed NOx sensor B. The sensor and its control unit are one part and are replaced together.
- The sensor's fuse or power supply.
- A problem on the CAN network between the sensor and the engine ECU.
At the garage: what to ask for
Supply and ground measured at the sensor connector and a check of the wiring under the car, before replacing the sensor, which is an expensive part. After replacement, on some cars the new sensor has to be registered with the garage's tool.
What DrivePulse shows
DrivePulse shows U029E when the control unit that stored it answers on the OBD port, and its card warns straight away about the countdown on diesels with AdBlue. It also tells you whether the code is pending or confirmed.
If AdBlue codes appear together with U029E, DrivePulse shows them side by side: useful for explaining the full picture at the garage.
Frequently asked questions
Can I drive with U029E?
To the garage, without putting it off: on many diesels with AdBlue a countdown starts, after which the engine won't restart.
Does the NOx sensor need replacing?
Not first. The fault is often in the wiring or connector under the car; the sensor is replaced after those have been checked.
What is NOx sensor B?
It's the second nitrogen oxide sensor, usually fitted after the SCR catalyst, which checks how well the AdBlue system is working.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.