What to look at in live data
If the car reports EGR data, compare the opening the ECU asks for with the EGR error the ECU itself calculates: a large, steady error, always on the same side, says exhaust gas is not getting through as it should.
An indirect check: when the valve opens, on a diesel the mass air flow sensor reads less fresh air; on a petrol engine intake manifold pressure rises a little. If nothing changes when the valve opens, the passage is clogged with soot (valve, ducts or EGR cooler) or the valve is not moving.
How serious is it, can you drive?
Severity is medium. You can drive gently: the engine runs and the code doesn't damage it in the short term. Don't leave it for months, though: with too little EGR flow a petrol engine can pink under load, a diesel puts out more nitrogen oxides, and while the light is on the inspection test is at risk. If the car loses power, jerks or goes into limp mode, have it checked soon.
Read P0401 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat the EGR valve does
EGR stands for exhaust gas recirculation. The valve sends part of the exhaust gas back into the intake. That makes combustion cooler and forms fewer nitrogen oxides, NOx. The ECU opens and closes it according to load and revs. Diesels often also have a small cooler that cools the gas before it goes back in.
What P0401 means
P0401 means insufficient EGR flow. The ECU commanded the valve to open but didn't see the effect it expected, for example in manifold pressure or air flow. So less gas is passing than it should.
Most likely causes
- Carbon build-up in the valve or passages. By far the most common cause.
- A valve that won't open, because of an actuator problem.
- Less often, a sensor measuring wrong or a leaking pipe.
Carbon builds up with short trips, lots of idling and an engine that stays cold, especially on diesels.
Symptoms
Often there's only the check engine light. Sometimes, on a petrol engine, you hear pinking under acceleration. Heavily clogged diesels can bring black smoke, loss of power and a rough idle. At an emissions test, nitrogen oxides can come out above the limit.
What to do
- Take a long drive at steady revs, on a main road or motorway, with the engine warm. Sometimes that's enough to unstick the valve.
- If the code returns, the valve and passages need mechanical cleaning, or the valve needs replacing.
- Don't have the EGR disabled. It's illegal, increases emissions and fails the inspection.
When to see a mechanic
- The code returns after a long drive.
- The car loses power, jerks or goes into limp mode.
- Other intake or boost related codes are present.
What DrivePulse shows
DrivePulse reads the code and opens the P0401 card, with the causes, what to check and whether you can drive. Statistics show how much time you spend with a cold engine and how many minutes it takes on average to warm up, which are exactly the conditions in which the EGR gets dirty.
After cleaning, the Before the inspection card shows when the monitors are ready again. The code is marked as resolved when the ECU stops reporting it.
Frequently asked questions
Does the code clear by itself?
If the valve starts working again, the ECU turns off the light after a few drive cycles without the fault, and the code is marked as resolved. If it returns after a few days, the valve needs cleaning or replacing.
Can I clean the EGR valve myself?
On many cars the valve comes off with a few tools, but you need new gaskets, care with the connectors and some experience. If you're not sure, it's a garage job, and it's often worth cleaning the passages too.
P0401 on petrol and diesel?
The code is the same, but on diesels carbon build-up is much more common, because the exhaust carries more soot. On petrol engines it's more often a valve or actuator problem.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.