EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Exhaust, catalytic converter and DPF
  4. P2453

P2453: diesel particulate filter differential pressure sensor range/performance

The differential pressure sensor tells the ECU how full the DPF is. If it reads wrong, the ECU decides badly when to regenerate. The trouble is often in a small hose.

Get DrivePulse

What to check before the garage

  • With the engine cold, look at the two hoses from the filter to the sensor: intact, pushed fully on, no kinks or melting near the exhaust.
  • If the exhaust or the filter has recently been worked on, tell the garage: swapped hoses are a common mistake.
  • Check the sensor connector.

What to look at in live data

If the car reports differential pressure across the particulate filter, look at it at three moments. With the engine off and the ignition on it should read zero or close: any other value means a drifting sensor or a blocked pipe. At idle with the engine warm it should be low and steady; with P2453 it often stays put, or doesn't rise when exhaust flow rises.

The third moment is under acceleration, with the phone in the hands of the person in the passenger seat: differential pressure should climb with load and fall back when you lift off. If it stays flat, look at the two pipes between filter and sensor (loose, melted, full of condensation, or swapped after a repair); if it reads high even with a freshly regenerated filter, the sensor is giving a wrong value and the ECU may call for regenerations that aren't needed.

How serious is it and can you drive?

Severity is medium. You can drive gently, but without a reliable sensor the ECU may regenerate too often, wasting fuel, or too rarely, letting the filter load up. Don't leave it for weeks, or a cheap problem turns into a clogged filter.

Read P2453 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The differential pressure sensor measures the pressure difference between the inlet and outlet of the particulate filter, through two small hoses. The more soot the filter holds, the bigger the difference, and the ECU uses this figure to decide when to start a regeneration. With P2453 it says the sensor's values aren't believable: too high or too low for those revs and that load, or not zero with the engine off.

Symptoms

  • Check engine or DPF light on.
  • Regenerations too frequent, or a filter loading up without regenerating.
  • Sometimes limp mode.
  • Higher fuel consumption if the ECU regenerates more than needed.

Most likely causes, in order

  • A small hose between filter and sensor cracked, disconnected, kinked or blocked with soot or condensation.
  • Hoses swapped after work on the exhaust.
  • The sensor drifting or failed.
  • A corroded connector.

At the garage: what to ask for

A reading of the sensor value with the engine off, which should be close to zero, and at idle, then a check of the hoses, including blowing through them to see they're clear. The sensor gets replaced after ruling out the hoses.

What DrivePulse shows

DrivePulse reads P2453 and opens its card, which suggests keeping an eye on DPF status meanwhile. In Health, DPF status shows the last regeneration, the history and how loaded the filter is compared with your trips: if regenerations start behaving oddly, that fits with a sensor reading wrong.

When the filter is cleaning you see it live on the Dashboard, in the pill at the top of the iPhone and on CarPlay.

Frequently asked questions

Can I drive with P2453?

Yes, gently. But not for weeks: without a reliable sensor the filter can load up without the ECU noticing.

Does the sensor need replacing?

Not always. The problem is often a cracked, disconnected or blocked hose. The sensor comes after.

How is it related to P2002?

A sensor reading wrong can also bring up P2002, because the ECU judges the filter's efficiency from that very pressure.

Why should the value be zero with the engine off?

Because without exhaust flow there's no pressure difference across the filter. If the sensor still reads something, the sensor or a hose is giving a false value.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes