What to do
- A long drive won't help: regeneration burns soot, not ash.
- Ask the garage about professional filter cleaning, which often costs much less than a new filter. Get more than one quote.
- After cleaning or replacement, the ECU must be updated: otherwise it keeps thinking the filter is full.
- Don't remove the filter: it's illegal and the car will fail its inspection.
What to look at in live data
If the car reports estimated ash in the DPF, that is exactly the value the ECU uses for this code: it grows slowly, mile after mile, and P242F appears when it passes the limit. Differential pressure right after a complete regeneration tells you the rest: if it stays high even with estimated soot close to zero, what is blocking the filter is ash, which does not burn.
After the filter is cleaned or replaced, the ash value in the data should drop back close to zero. If it stays high, the ECU has not been updated and will keep treating the filter as full: tell the garage that did the job.
How serious is it and can you drive?
Severity is high. A full filter raises exhaust back pressure, the engine runs worse and the ECU limits power. Only drive as far as the garage: carrying on won't fix it, because ash doesn't go away by itself.
Read P242F on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The DPF traps two different things. Soot, which burns during regenerations. And ash, which comes mainly from the additives in the engine oil that a diesel burns in small amounts: ash doesn't burn and stays in the filter, mile after mile. Many ECUs estimate how much ash has built up, and with P242F they say it has passed the threshold.
It's an end-of-life code for the filter: it usually arrives after a high mileage, sooner if the engine burns oil or the wrong oil has been used.
Symptoms
- DPF light or check engine light on.
- Ever more frequent regenerations, with rising fuel consumption.
- Loss of power and limp mode.
Most likely causes, in order
- A filter at the end of its life, after many miles of accumulated ash.
- The wrong engine oil, without the low-ash specification required for cars with a DPF.
- An engine burning oil, through a worn turbo or piston rings, sending more ash to the filter.
- An ash counter that wasn't reset after the filter was cleaned or replaced.
At the garage: what to ask for
A reading of estimated ash and differential pressure, a check of the engine's oil consumption, then cleaning or replacing the filter, with the ECU updated. Also ask which oil to use from then on.
What DrivePulse shows
DrivePulse reads P242F and opens its card, which explains straight away that ash can't be removed by regeneration. In DPF status under Health you find the regeneration history: if regenerations have recently become much more frequent, that fits with a filter filling up.
In the maintenance deadlines you can record the oil type and the last change, so at the next service you know what to ask for.
Frequently asked questions
Can a motorway drive fix P242F?
No. Regeneration burns soot, not ash. With P242F the filter needs cleaning or replacing.
Is it better to clean or replace the filter?
Professional cleaning is often enough and costs much less. It's replaced if the filter is damaged or cleaning doesn't bring the pressure back into range.
Which oil should I use?
The one with the manufacturer's specification for cars with a particulate filter, low in ash. A different oil fills the filter faster.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.