What to check before the garage
- See whether other codes are stored: fix those first, because they're often what blocks the cleaning.
- Keep the tank above the reserve for a few days.
- If you can, drive a long trip at a steady speed on an open road, without switching off halfway, to give the filter time to clean itself.
- Check the oil level: if it rises instead of dropping, diesel may have got into the oil from failed regenerations.
What to look at in live data
P246B doesn't point to a broken part: it says the ECU wanted to regenerate the particulate filter but driving conditions didn't allow it, usually because of too many short or slow trips. In the standard data, watch coolant temperature on your usual routes, read by the person in the passenger seat (it should reach about 90 °C and stay there) and, if the car reports them, filter differential pressure and exhaust gas temperatures.
A route that helps regeneration is 15 to 20 minutes at steady speed on an open road or motorway, above about 2,000 rpm: watching exhaust gas temperatures, again with the phone in the passenger's hands, shows whether the regeneration starts and finishes. If the code comes back even with long trips, the cause lies elsewhere: a temperature or pressure sensor that misreads, a thermostat stuck open, an oil level too high from dilution with diesel.
How serious is it and can you drive?
Severity is medium. You can drive gently. If the light flashes or the car goes into limp mode, go to a garage soon: an overloaded filter can be damaged.
Read P246B on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The control unit constantly estimates how much soot is in the filter. When the time comes, it starts a regeneration: it raises the exhaust gas temperature for a few minutes and the soot burns. To do that, though, it needs specific conditions: a warm engine, a certain engine speed, and no fault that makes the process risky.
P246B says those conditions were missing too many times, or for too long. It isn't a fault in the filter itself: it's the sign that cleaning can't start or can't finish. If things carry on like this, codes for an overloaded filter such as P2463 follow.
Symptoms
- Particulate filter light or check engine light on.
- Signs of attempted regenerations: fan running with the engine off, higher idle, higher fuel consumption.
- Once the filter is loaded, less power or limp mode.
- Sometimes no symptoms, just the code.
Most likely causes, in order
- Short trips: the engine doesn't stay warm long enough, and the regeneration doesn't start or gets cut short.
- Interrupted regenerations, switching the engine off just while the filter was cleaning itself.
- Another fault already stored: with a faulty exhaust temperature or pressure sensor, or an EGR valve problem, many control units don't attempt regeneration.
- An engine that doesn't warm up, for example because of a thermostat stuck open: the coolant never reaches temperature and the control unit waits.
- Little diesel in the tank: on some cars regeneration doesn't start with the low fuel light on.
Why driving more isn't always enough
If the cause is the way the car is used, a long trip now and then fixes it and the code doesn't come back. If another fault is blocking regeneration, though, you can drive as far as you like: the control unit won't try until that fault is gone.
That's why the order matters: first the other codes and an engine that warms up, then cleaning the filter. A forced regeneration at the garage on a filter with a faulty sensor doesn't last long.
At the garage: what to ask
Reading how much soot and ash is in the filter and which conditions blocked regeneration, and checking the exhaust sensors and the engine temperature. In order of cost: fixing the fault that blocks it, a regeneration with the diagnostic tool, an oil change if the oil is diluted, cleaning the filter, and only last a new filter.
What DrivePulse shows
DrivePulse reads P246B and opens the particulate filter card, with the advice of a long trip at a steady speed and the oil level check; it also tells you whether the code is pending or confirmed.
If exhaust sensor or thermostat codes such as P0128 show up too, you see them in the same list: they're often the reason the cleaning doesn't start. In Statistics, the time you spend with a cold engine tells you how many of your trips are too short for the filter.
Frequently asked questions
Can I drive with P246B?
Yes, gently. If the light flashes or the car goes into limp mode, go to a garage soon.
What's the difference from P2463?
P2463 says the filter is already overloaded. P246B says the cleaning couldn't start or finish: it often comes first, and it's the right time to act.
Is one long motorway trip enough?
If the cause is short trips, often yes. If another fault is blocking regeneration, no: that has to be fixed first.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.