What to look at in live data
P0400 says EGR flow isn't what was expected, without saying whether too much or too little. In the standard data, watch commanded EGR and the EGR error over a stretch of light, steady load where the valve works, with the phone in the hands of the person in the passenger seat: an error that is always negative or always positive tells you which way it is wrong. On engines with a mass air flow sensor, measured fresh air should drop a little when EGR opens: if it never changes, no exhaust gas is getting through.
Low flow is almost always carbon: in the valve, the manifold passages or, on diesels, the EGR cooler. Excess flow is a valve that won't close. Before taking anything apart, check whether commanded EGR really changes (if it stays at zero, the ECU isn't using it at that moment) and whether the engine has other codes for the same valve, such as P0401, P0402 or P0403, which narrow things down.
How serious is it, can you drive?
Severity is medium. If the engine runs well you can drive gently, but don't leave it for months: the carbon builds up, and a stuck valve can add a rough idle and stalling. If the engine stalls at idle, get to a garage soon.
Read P0400 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The EGR valve, exhaust gas recirculation, sends part of the exhaust back into the intake to lower combustion temperature and nitrogen oxides. The ECU knows how far it opens the valve and checks the result, for example with the pressure or air flow sensors.
With P0400 the measured flow doesn't match the commanded flow: too little or too much. P0401 is the specific case of insufficient flow; P0400 is the more general code, and some cars set it instead.
Symptoms
- Engine light on.
- With too little flow: often nothing unusual while driving, but more nitrogen oxides in the exhaust.
- With the valve stuck open: rough idle, hesitation or stalling, and black smoke on diesels.
- On diesels, sometimes less power.
Most likely causes, in order
- A carbon-coked EGR valve, typical of diesels that mostly do town driving and short trips.
- The actuator or solenoid that moves the valve.
- Blocked EGR passages, including the EGR cooler on diesels.
- A vacuum hose cracked or off, on cars that work the EGR by vacuum.
- A pressure or air flow sensor reading wrong and making the flow look wrong.
What to check before the garage
- How you drive: lots of short trips, with an engine that never warms up, coke up the EGR.
- An hour at steady speed on an open road helps clean it, if the build-up is light.
- Fuel additives do little: if the valve is coked, it needs mechanical cleaning.
- With the engine off, the valve connector and, if there is one, the vacuum hose: no cracks, nothing loose.
At the garage: what to ask for
A live reading of commanded and actual valve opening, an actuator test, then removing the valve to see how much carbon there is. In order of cost: cleaning the valve, replacing the valve, cleaning or replacing the EGR cooler, which is the most expensive item.
What DrivePulse shows
DrivePulse reads P0400 and opens its card, with the tip of an open-road drive at steady speed and the warning that additives do little; it also tells you whether the code is pending or confirmed.
Statistics show how much time you drive with a cold engine and how many minutes it takes on average to warm up: exactly the conditions in which the EGR gets dirty.
Frequently asked questions
Can I drive with P0400?
Yes, gently, if the engine runs smoothly. Don't put it off too long: the carbon builds up. If the engine stalls at idle, garage soon.
What's the difference from P0401?
P0401 says the flow is insufficient. P0400 says the flow isn't what's expected, without saying which way: it's the more general code.
Can a long drive be enough?
If the build-up is light, an hour at steady speed helps. If the valve is heavily coked, it needs mechanical cleaning or replacement.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.