EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Exhaust, catalytic converter and DPF
  4. P0403

P0403: EGR control circuit malfunction

The ECU controls the EGR valve with an electrical signal. With P0403 that control has a fault: the circuit is open, shorted or out of range. The connector is often to blame, since it sits near the exhaust, in the heat.

Get DrivePulse

What to look at in live data

P0403 is an electrical fault in the EGR valve control: the ECU drives it and finds the circuit open or shorted. In the standard data, watch commanded EGR and the EGR error with the engine warm, over a stretch of light, steady load where EGR works most, with the phone in the hands of the person in the passenger seat: if the command changes and the error stays large, the valve isn't responding; if the command stays at zero too, the ECU has already shut it off for protection.

The check is done with the engine off, at the valve connector: power with the ignition on, continuity of the control wire back to the ECU, and resistance of the motor or solenoid (a few ohms on many valves). On diesels the connector often sits near the hot manifold and the wires get cooked; if the valve is vacuum operated, the code concerns the solenoid valve that controls it.

How serious is it, can you drive?

Severity is medium. If the engine runs well you can drive gently to the garage. If the idle is rough, the engine stalls or power drops, don't put it off: a valve stuck open makes the engine unsteady just when you're manoeuvring.

Read P0403 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The EGR valve sends part of the exhaust gas back into the intake: it lowers combustion temperature and cuts nitrogen oxides. The ECU opens and closes it with an electric actuator, a solenoid or a small motor depending on the car.

With P0403 the ECU sees an electrical fault in the circuit that drives the valve: the signal isn't getting through, or the current is too high or too low. That is different from P0400 and P0401, where the command gets through but the gas flow isn't what's expected.

Symptoms

  • Engine light on, often with nothing else unusual.
  • If the valve stays open: rough idle, hesitation or stalling.
  • On diesels, sometimes less power: the ECU limits the engine to protect it.
  • More nitrogen oxides in the exhaust, which you can't feel but which count at the emissions test.

Most likely causes, in order

  • The EGR valve connector loose, corroded or oily.
  • The wiring to the valve damaged by heat or rubbing on the engine.
  • A failed valve actuator: the internal coil or motor.
  • The valve stuck with carbon: the motor can't move it and the circuit flags an error.
  • More rarely, a fuse or the ECU.

What to check before the garage

  • With the engine off and cold, the EGR valve connector: it must be pushed fully home, with no oil and no green contacts.
  • The nearby wiring: no melted sleeves, no wires resting on the exhaust.
  • Whether the code is only pending or already confirmed: a pending code can be a passing loose contact.

At the garage: what to ask for

An actuator test with the diagnostic tool, which opens and closes the valve, and a measurement of the command signal and resistance. Then repair of the connector or wiring, cleaning if the valve is stuck with carbon, and replacement only if the actuator has failed. Connector and wiring cost little; a new valve is the most expensive item on the list.

What DrivePulse shows

DrivePulse reads P0403 and opens its card, with the advice to start from the EGR valve connector; it also tells you whether the code is pending or confirmed.

If P0400 or P0401 show up too, DrivePulse lists them together: a command that doesn't get through also changes the gas flow, and the codes should be read as one problem.

Frequently asked questions

Can I drive with P0403?

Yes, gently as far as the garage, if the engine runs smoothly. If the idle is rough or it stalls, better not to wait.

What's the difference from P0400 and P0401?

P0403 is an electrical fault in the valve's control circuit. P0400 and P0401 say the command gets through but the gas flow isn't what's expected.

Will cleaning the EGR valve fix P0403?

Only if the motor can't move a valve stuck with carbon. If the fault is in the connector, the wiring or the actuator, cleaning won't be enough.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes