What to look at in live data
If the car reports particulate sensor temperature, watch it with the engine warm: when the sensor heats itself to clean off, it should rise a long way, to several hundred degrees, then come back down. If it stays flat, shows an impossible value or drops out, the circuit that measures the sensor's temperature is not working.
Check the DPF data too, if available: with normal differential pressure and estimated soot, the filter is doing its job and the fault lies with the sensor or its wiring, which runs close to the hot exhaust. Keep an eye on them anyway, because without the sensor the ECU watches the filter with less information.
How serious is it, can you drive?
Severity is low. The engine and the filter aren't harmed by this code, and you can drive gently without hurry. But while the light stays on the inspection test is at risk, and a sensor that isn't working can't warn you if the filter fails one day.
Read P24C6 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The particulate matter sensor sits in the exhaust after the DPF. It collects the particles that get past the filter and, if too many arrive, tells the ECU the filter isn't holding them as it should. To clean itself and measure properly, it heats itself up and monitors its own temperature.
P24C6 concerns that temperature circuit: the signal is missing or out of limits. It isn't the DPF pressure sensor, the one that measures how full the filter is, and it doesn't mean the filter is blocked.
Symptoms
- Engine light on, almost always with no other symptoms.
- No loss of power in most cases.
- Sometimes the code comes straight back after being cleared.
- It may appear after a DPF regeneration, when the exhaust is very hot.
Most likely causes, in order
- A failed particulate matter sensor, in its heating element or the one that measures temperature.
- The connector or wiring, damaged by exhaust heat or road dirt.
- An exhaust leak near the sensor, which upsets the measurement.
- The ECU, very rarely.
What to check before the garage
- If you can see it without removing anything, look at the sensor connector under the car: it should be plugged in, with no baked or torn wires.
- Note whether the code appears after long drives or after a regeneration: a useful clue.
- Keep an eye on the DPF status: this code on its own doesn't mean a blocked filter.
At the garage: what to ask for
A check of the connector and wiring under the car, then a measurement of the sensor's heating element and temperature signal. If the sensor has failed it is replaced; the DPF isn't touched for this code.
What DrivePulse shows
DrivePulse reads P24C6 and its card makes clear straight away that this isn't the DPF pressure sensor but the one that checks no soot gets past the filter; it also tells you whether the code is pending or confirmed.
On suitable cars the DPF status shows how full the filter is and the regenerations: if they look regular, that confirms the problem is the sensor and not the filter.
Frequently asked questions
Can I drive with P24C6?
Yes, without hurry: it doesn't harm the engine or the filter. But with the light on, the inspection test is at risk.
Does it mean the DPF is blocked?
No. P24C6 is about the sensor after the filter. How full the DPF is comes from the pressure sensor.
Does the DPF need replacing?
No. For this code the connector, wiring and particulate matter sensor are checked.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.