EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P2279

P2279: intake air system leak

The ECU compares the air measured at the inlet with what the engine actually breathes. With P2279 the numbers don't add up: air is getting in somewhere that nobody has measured.

Get DrivePulse

What to look at in live data

P2279 means air is getting in that the ECU did not measure. In live data it shows in the fuel trims: with the engine warm and at idle they are high and positive, and they drop as revs rise, because at higher revs the same leak is a smaller share of the total air.

On a petrol engine, intake manifold pressure at idle can be higher than usual. Typical leaks are cracked vacuum hoses, the intake manifold gasket, the hose after the mass air flow sensor and the crankcase ventilation valve. A garage finds them quickly with a smoke test.

How serious is it, can you drive?

Severity is medium. You can drive gently, but don't put it off: with extra air the mixture runs lean, the engine works worse and misfires can follow in the long run. If the idle becomes very unstable or the engine stalls, have it seen straight away.

Read P2279 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The airflow sensor, or the manifold pressure sensor, measures the air entering the engine, and the ECU meters fuel on that value. If there's a gap after the sensor, the engine also draws in air that hasn't been counted.

With P2279 the ECU has noticed that the measured air and the way the engine behaves don't match, for example with fuel trims climbing higher and higher. The code says there's a leak, not where it is.

Symptoms

  • Rough or slightly high idle, especially from cold.
  • A whistle or hiss from the engine bay with the engine running.
  • Hesitation when accelerating and higher fuel use.
  • Often together with P0171 (lean mixture) and sometimes idle codes.

Most likely causes, in order

  • A cracked intake hose or loose clamp between the airflow sensor and the engine: the most frequent and simplest cause.
  • The crankcase ventilation valve or diaphragm broken: a common fault on many modern petrol engines, often with a whistle.
  • The intake manifold gasket no longer sealing.
  • A disconnected hose, such as the brake booster or fuel vapour hose.

What to check before the garage

  • With the engine running, listen carefully near the engine: a whistle or hiss points to where air gets in. Keep hands and clothing away from belts and the fan.
  • With the engine off, check the hoses and clamps between the air filter and the engine: flex the rubber hoses gently to reveal cracks.
  • Check that the oil filler cap is closed properly and its seal is intact: on some engines a leak there is enough to set the code.

At the garage: what to ask for

A smoke test: harmless smoke is fed into the intake and the garage watches where it comes out. It finds the leak in minutes, even when it's hidden under the manifold. The leak should be ruled out before the airflow sensor or O2 sensors are replaced.

What DrivePulse shows

DrivePulse reads P2279 and its card starts with the first check: with the engine running, listen near the engine for where the air whistles in. It also tells you whether the code is pending or confirmed.

Live fuel trims (STFT and LTFT) are useful: with a leak they usually go positive at idle and drop when you accelerate. After the repair they should return close to zero.

Frequently asked questions

Can I drive with P2279?

Yes, gently, but have it checked soon: a lean mixture makes the engine run badly in the long run.

Why does it appear with P0171?

Because the extra air leans the mixture, and P0171 is the lean mixture code. Fix the leak and both go away.

Should I replace the airflow sensor?

Not first. A failed airflow sensor would set its own codes; with P2279 the leak is looked for first.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes