What to check before the garage
- Look in the handbook for the fuse of the AdBlue system or reductant module and check whether it's intact.
- Think about whether the car recently went through a deep puddle or had its underside pressure-washed: it's a valuable clue.
- Note what the countdown shows, if there is one, and how much it drops on each trip.
What to look at in live data
With U010E the engine ECU no longer hears the module that manages AdBlue, and the nitrogen oxide reduction system stops working: AdBlue warnings and a countdown of the kilometres left before the engine won't restart often appear straight away. If the car reports the reductant system in the standard data, see whether level and status stay readable or disappear: if they disappear, communication is exactly the problem.
The AdBlue module often sits near the tank, under the car or in the boot, where water and salt reach it: connector, fuse and ground are the first checks. Watch the control module voltage while cranking and after a long stop in the cold too: the AdBlue heaters draw a lot of current, and a borderline battery can make the module drop out, typically in winter. At the garage it is worth reading the codes of the AdBlue module itself, if it answers.
How serious is it and can you drive?
Severity is medium. You can drive, gently, but get it fixed soon: if the countdown appears, at zero the car may not restart after being switched off until the fault is fixed.
Read U010E on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The car's control units swap messages all the time over a two-wire network. The engine ECU expects, at regular intervals, those of the AdBlue module: fluid level, temperature, pump status. If they stop arriving for a while, it stores U010E.
The code says the conversation is missing, not which part is broken. On many cars the AdBlue module sits near the fluid tank, under the car or in the boot, in an area exposed to water and salt: that's why the connectors are a frequent suspect.
Symptoms
- Check engine light or AdBlue warning on.
- A mileage countdown on the dashboard: at zero the car may not restart after being switched off.
- The AdBlue level gauge disappearing or showing a nonsense value.
- The engine usually runs normally, sometimes with less power.
Most likely causes, in order
- The AdBlue module's power supply: a blown fuse, a relay or a corroded ground.
- The module connector with water inside or corroded.
- The network wires between that module and the rest of the car, damaged under the body.
- A weak battery, which makes the most sensitive units drop out for a moment at every start.
- The AdBlue module itself failing, which is rarer.
The countdown
If the car can no longer control the AdBlue, emissions rules require it to warn you and then prevent a restart. The mileage countdown is exactly that warning: it won't go away until contact with the module is back and the fault is fixed.
That's why U010E shouldn't be left alone: even if the engine runs well, it's worth getting the car to the garage with a good margin left.
At the garage: what to ask
Reading the codes of all control units, checking the AdBlue module's power and ground, and testing the network up to it. In order of cost: fuse or connector, wiring repair, the battery if it's weak, and only then the module.
What DrivePulse shows
DrivePulse shows U010E when the control unit that stored it responds on the OBD port, and opens the AdBlue system card with the warning about the countdown; it also tells you whether the code is pending or confirmed.
In Health, the battery voltage with the engine off and during cranking tells you whether the power supply is borderline. If AdBlue system codes such as P20EE or P20E8 show up too, it lists them alongside.
Frequently asked questions
Can I drive with U010E?
Yes, gently, but get it fixed soon: if the countdown appears, at zero the car may not restart after being switched off.
What's the difference from P20EE?
P20EE says the AdBlue catalyst isn't cutting nitrogen oxides enough. U010E says contact with the module that runs the AdBlue is missing altogether.
Does the AdBlue module need replacing?
Not first. More often it's a fuse, a connector with water in it or a damaged wire under the car. The module is replaced only when the tests point to it.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.