EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P219A

P219A: bank 1 air/fuel ratio imbalance

Look at the short term fuel trims with the engine warm at idle: with an imbalance between cylinders they swing wide and irregularly instead of making small steady corrections. In mode 06, a cylinder with a higher misfire count is the first to check. If the engine runs smoothly, carefully to the garage; if it shakes or the light flashes, stop.

Get DrivePulse

What to look at in live data

Look at short-term fuel trims with the engine warm and at idle: with an imbalance between cylinders they swing more than usual, in wide, irregular jumps instead of small, steady corrections. The oxygen sensor before the catalytic converter moves erratically too.

If the car counts misfires per cylinder in its on-board tests (mode 06), a cylinder with a higher count than the others is the first to look at, even if no misfire code has been set: that is often where the injector delivers too much or too little.

How serious is it, can you drive?

Severity is medium. If the engine runs smoothly, drive carefully to the garage. If it shakes badly or the light flashes, stop as for P0300: a cylinder that isn't burning properly sends unburnt fuel into the catalyst and can damage it quickly.

Read P219A on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The O2 sensor sees the exhaust from every cylinder one after another. If one of them burns a different mixture, the sensor signal wobbles on every revolution in a recognisable way, and the ECU picks it up.

P219A says exactly that: the mixture isn't the same in all bank 1 cylinders. It doesn't say which cylinder, or whether it's richer or leaner: that takes more data and a few tests.

It's a check the ECU runs on more modern petrol engines. It's there to catch a small imbalance early, before it turns into a misfire or damages the catalyst.

Symptoms

  • Engine light on.
  • Engine shaking slightly at idle or under light acceleration.
  • Higher fuel consumption.
  • Sometimes misfires on one cylinder (P0301, P0302 and so on).

Most likely causes, in order

  • An injector that's dirty and sprays too little, or drips and sprays too much.
  • An air leak near a single cylinder, for example from the manifold gasket.
  • A coil or spark plug working poorly on one cylinder.
  • Low compression on one cylinder, from valves or rings.

What to check before the garage

  • If misfire codes for a specific cylinder appear with P219A, that cylinder is the first suspect.
  • If there's P0171 or P0172, start with the air leak or rich mixture checks: they often explain P219A too.
  • Listen to the engine at idle: a hiss near the manifold points to a leak.
  • If the car has recently had work on the injectors, spark plugs or manifold, start there: a connector left unplugged or a badly fitted gasket is enough to set the code.

At the garage: what to ask for

A cylinder-by-cylinder test: injector balance, coil swaps, a compression check. That finds the cylinder and the cause before sensors or injectors are replaced at random.

What DrivePulse shows

DrivePulse reads P219A and opens its card, and shows alongside it any misfire or mixture codes that help find the cylinder. It also tells you whether each code is pending or confirmed.

Live fuel trims show whether, overall, the ECU is adding or taking away fuel.

Frequently asked questions

Can I drive with P219A?

It depends: if the engine runs smoothly, carefully to the garage. If it shakes badly or the light flashes, stop.

Does the O2 sensor need replacing?

Hardly ever. The sensor sees the imbalance, it doesn't cause it: the cause is in a cylinder.

How do you find the cylinder?

From any misfire codes, and with the garage's tests on injectors, coils and compression.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes