EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Cooling and oil
  4. P261A

P261A: coolant pump B control circuit open

Many recent engines have, besides the main pump, a second electric coolant pump controlled by the ECU. With P261A the ECU sees that pump's circuit as open: it commands the pump, but no current flows. The first thing to watch is the engine temperature.

Get DrivePulse

What to look at in live data

Coolant pump B is usually an auxiliary electric pump: it circulates coolant through the turbo, the heater or the intercooler, sometimes even with the engine off. Its status isn't among the standard OBD2 data, but its effects are: watch coolant temperature and, if reported, charge air temperature after the intercooler, with the phone in the hands of the person in the passenger seat when the car is moving. An unusual rise after a hard pull, or cabin heating that stays lukewarm at idle, points to it.

P261A says the control circuit is open: the ECU drives the pump and finds no load. The check is done with the engine off: the pump connector (often low in the engine bay, exposed to water and salt), the fuse or relay, continuity of the wire to the ECU. On cars where the pump cools the turbo after shutdown, you can sometimes hear it run for a few minutes: if you never hear it, that is another clue.

How serious is it, can you drive?

Severity is medium, and it depends on the temperature. If it stays normal, you can drive gently to the garage, avoiding long climbs, towing and long idling. If it rises, stop: a pump fault only matters for what it does to the temperature.

Read P261A on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The letter B means the second pump in the cooling circuit. On many cars it's an auxiliary electric pump: it helps cabin heating, cools the turbo or the exhaust gas recirculation, and sometimes keeps running for a few minutes after the engine is switched off.

With P261A the ECU, when it commands the pump, sees an open circuit: a broken wire, an unplugged connector or a burnt-out pump motor. The code doesn't say the engine is overheating, only that the pump isn't receiving the command.

Symptoms

  • Check engine light on, sometimes with no other signs.
  • Cabin heating that blows only lukewarm, especially at idle.
  • Engine temperature climbing more than usual in traffic or uphill.
  • After switching off, you no longer hear the hum of the pump that used to run.

Most likely causes, in order

  • The pump connector, corroded or loose: the pump sits low down, exposed to water and dirt.
  • The pump fuse or relay.
  • The pump's electric motor burnt out, often after the impeller seized.
  • The wiring between the pump and the ECU, damaged by heat.
  • Less often, the ECU circuit that drives it.

What to check before the garage

  • With the engine cold, the coolant level in the expansion tank, never opening it when hot.
  • Traces of coolant or coloured crusts near the pump or under the car.
  • The auxiliary pump fuse: the manual tells you which one.
  • While driving, the temperature on the dashboard: it should stay where it usually sits.

When to stop

If the temperature rises above normal or the temperature warning light comes on, stop as soon as it's safe and switch off the engine. Driving with an overheated engine can ruin the head gasket in minutes.

Wait for it to cool before opening the bonnet, and never open the expansion tank when hot: the coolant is under pressure and can scald.

At the garage: what to ask for

Commanding the pump from the scan tool to hear whether it runs, and measuring power and ground at its connector. Then a pressure test of the cooling circuit. In order of cost: connector or fuse, relay, wiring, new pump.

What DrivePulse shows

DrivePulse reads P261A and opens the coolant pump card, with the advice to watch the temperature and stop if it rises; it also says whether the code is pending or confirmed.

In live data you'll find the coolant temperature: that's the number to keep an eye on until the pump is fixed, especially in queues and uphill. While driving, the passenger watches it, not the driver.

Frequently asked questions

Can I drive with P261A?

If the engine temperature stays normal, yes, gently to the garage. If it rises or the temperature light comes on, stop and switch off the engine.

What is pump B?

It's the second coolant pump. On many cars it's electric and helps the heating or cools the turbo, even after the engine is switched off.

Why does the heating blow lukewarm?

On many cars it's the auxiliary pump that pushes hot coolant to the cabin heater, especially at idle. If it doesn't run, the heating suffers.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes