What to check before the garage
- The battery and terminals: tight, clean, with no corrosion.
- Think back to whether water recently got into the cabin or engine bay, or an accessory was fitted: valuable clues.
- Note when it happens: at start-up, over bumps, in the rain. For a network fault it's the most useful information.
What to look at in live data
With the network between modules switched off, much of the data doesn't arrive or arrives in bursts: the very fact that your reader connects and reads engine data tells you that at least that part of the network works. Watch whether reading stops, whether all values get stuck together, or whether several lost communication codes appear (U0100, U0101, U0121): the overall picture shows how far the fault reaches.
Then check the control module voltage: a network that shuts down while cranking, or with the battery below 12 V and the engine stopped, is often just a power problem. If the voltage is good, the fault is in the network wires (a shorted cable, a connector with water) or in a module that disturbs all the others: at the garage, modules are unplugged one at a time until the network comes back.
How serious is it, can you drive?
Severity is high. With the network down, important systems such as ABS, ESP and power steering can switch off together, and the cluster may stop showing speed and temperature. If many warning lights come on, stop somewhere safe. If the fault comes and goes and the car behaves normally, drive carefully only as far as the garage.
Read U0073 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The CAN network is made of two twisted wires linking the control units, with a resistor at each end. Every unit counts the errors it sees: if there are too many, it stops transmitting so as not to disturb the others. This state is called bus off.
U0073 means a control unit has gone bus off on network A, usually the main engine network. The fault can be a shorted or broken wire, a connector with water in it, or another control unit sending bad messages and throwing the whole network into trouble.
Symptoms
- Many warning lights on at once.
- Rev counter, speedometer or temperature gauge stop working.
- Automatic gearbox in limp mode, ABS and ESP disabled, heavier steering.
- In the worst cases, the engine won't start or stalls.
Most likely causes, in order
- A CAN network wire shorted or broken, often where the harness flexes or rubs.
- Water or corrosion in a connector, for example after leaks from the windscreen or the engine bay.
- A faulty control unit jamming the network.
- A weak battery or a bad ground.
- Aftermarket accessories wired into the network, such as alarms or trackers, badly installed.
At the garage: what to ask for
A reading of every control unit's codes, a measurement of the network with the battery disconnected, which should give a precise value, and then a search for the unit or the stretch of wire jamming the network, disconnecting units one at a time. Any added accessory is disconnected first.
What DrivePulse shows
DrivePulse shows U0073 when the control unit that stored it answers on the OBD port, and opens its card with causes, checks and when to stop. If the network is down at that moment, some units may not answer DrivePulse either: a sign the problem is happening now.
In Health, the resting battery voltage and the cranking test rule out a weak power supply.
Frequently asked questions
Can I drive with U0073?
It depends. If many lights come on or the steering gets heavy, stop somewhere safe. If everything works, carefully to the garage.
Does a control unit need replacing?
Not first. More often it's a wire, a connector with water in it or an added accessory. A unit is only replaced when the tests point to it.
What's the difference from U0100?
U0100 says contact with one specific unit, the engine ECU, is lost. U0073 says a unit has dropped off the whole network because of too many errors.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.