EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Electronics and communication
  4. U0155

U0155: lost communication with instrument panel cluster module

The instrument cluster is a control unit like the others and talks to them on the car's network. With U0155 another unit has stopped hearing it. Often it's a leftover from a flat battery; if instead the cluster goes dark or shows nonsense, you no longer have reliable warning lights.

Get DrivePulse

What to check before the garage

  • The battery: a low voltage when starting often sets these codes.
  • What isn't working: if the cluster works normally, the code is probably a leftover from a past event.
  • The instrument cluster fuses, shown in the owner's manual.
  • Whether the dashboard was taken apart recently or an accessory was fitted behind the cluster.

What to look at in live data

With U0155 the instrument cluster doesn't answer on the network: needles stuck or at zero, warning lights that don't come on, sometimes an engine that won't start because the immobiliser goes through the cluster. The first value to watch is the control module voltage with the ignition on and while cranking: the cluster is sensitive to dips, and a weak battery is enough to make it drop off the network for a few seconds.

If the voltage is good, try reading the codes of the cluster itself: if it doesn't answer your reader either, the fault is in its power supply (fuse, ground) or in the connector behind the dashboard. If it answers but the code comes back now and then, note when it happens: after a pothole, with the heating at full, only when cold. A fault that comes and goes with heat suggests cracked solder joints inside the cluster.

How serious is it, can you drive?

Severity is medium, but it depends on what you see. If the cluster works and there are no brake, steering or airbag warnings, you can drive gently to the garage. If the cluster is dark or shows wrong values, you have no reliable speedometer or warning lights: better not to drive until it's checked.

Read U0155 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The car's control units exchange messages constantly on a network of wires. The instrument cluster receives speed, revs and warnings from the others and sends some of its own, such as the mileage or the state of buttons.

With U0155 a control unit, usually the engine or gearbox one, hasn't received messages from the cluster for a certain time. The code says who's missing, not why: the cause can be in the cluster, its power supply or the wiring.

Symptoms

  • Several warning lights on at once, sometimes for no obvious reason.
  • Needles stuck, a cluster that goes dark or shows strange values.
  • Often no symptoms: the code stays stored from a past event, such as a flat battery.

Most likely causes, in order

  • The 12-volt battery weak or flat, or a jump start.
  • The cluster without power: a blown fuse or loose earth.
  • A network connector corroded or with water inside.
  • A network wire broken or pinched, for example behind the dashboard.
  • A failed instrument cluster.

At the garage: what to ask for

A scan of every control unit, to see which ones answer and which don't, and a check of the network up to the cluster, along with its power and earth. In order of cost: battery or fuse, connector or wire, repair or replacement of the cluster, which is the most expensive item.

What DrivePulse shows

DrivePulse reads U0155 and opens its card, which starts from the battery and fuses and helps you work out which function is missing; it also tells you whether the code is pending or confirmed.

In Health you find the battery voltage, and the cranking test captures the lowest voltage while the starter turns: if the battery is weak, that's the first thing to fix before hunting for a network fault.

Frequently asked questions

Can I drive with U0155?

If the cluster works and there are no brake, steering or airbag warnings, yes, gently. If the cluster is dark or shows wrong values, better not.

What's the difference from U0100?

They're the same family: U0100 says the engine control unit is missing, U0155 that the instrument cluster is.

Can a flat battery cause U0155?

Yes: a low voltage when starting can make messages drop for a moment. If the battery is weak, fix it first.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes