EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Electronics and communication
  4. P068A

P068A: ECM/PCM power relay de-energized too early

When you switch off the engine, the ECU stays on for a few more seconds to save its data. With P068A the power disappeared before it finished that job.

Get DrivePulse

What to look at in live data

The useful value is the voltage reaching the ECU, compared with the battery voltage measured at the terminals: with the ignition on and the engine off they should be almost the same. If the ECU reads noticeably less, there is a voltage drop in the wiring, the fuses or the relay that powers it.

The code is set at switch-off: after the ignition goes off the ECU has to stay powered for a few more seconds to save its data, and the relay cuts it too early. If it keeps coming back with a good battery and clean terminals, the garage checks the main relay, its supply and its ground.

How serious is it, can you drive?

Severity is low. The engine usually runs normally and you can drive gently. But if the code returns on its own, without battery work, have it checked: a relay or ground that's giving up could one day stop the engine starting.

Read P068A on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The engine ECU is powered through a main relay. When you turn the key or press the button to switch off, it doesn't shut down at once: it keeps the relay closed for a few more seconds, sometimes longer, to save learned adaptations, close valves and flaps and finish some checks.

With P068A the ECU noticed, on the next start, that the power went earlier than expected. The reason can be trivial, such as a battery disconnected right after switching off, or a relay or connection that isn't holding.

Symptoms

  • Engine light on, almost always with no other symptoms.
  • Sometimes the code appears once after battery work and never comes back.
  • Rarely a slightly rough idle after starting, because the ECU lost some adaptations.
  • If the relay really is failing, in the worst cases difficulty starting the engine.

Most likely causes, in order

  • The battery disconnected right after switching off, during a replacement or garage work.
  • A weak battery or oxidised terminals, letting the voltage drop just as the ECU shuts down.
  • A failed ECU main relay.
  • The wiring or ground between the relay and the ECU.

What to check before the garage

  • Think back to whether the battery was recently disconnected or replaced: if so and the code doesn't return over the following days, there's nothing to repair.
  • The battery voltage with the engine off: below 12.4 volts it's discharged and needs charging or checking.
  • The battery terminals: they should be tight and clean, with no white or green powder.

At the garage: what to ask for

A battery test, a main relay test and a check of the ECU grounds. If it appeared after a battery replacement, clearing the code and checking it doesn't return is enough.

What DrivePulse shows

DrivePulse reads P068A and its card reminds you that if it appeared after work on the battery and doesn't return in the following days, that's normal; it also tells you whether the code is pending or confirmed.

In Health you see the resting battery voltage and the cranking test: if the battery is healthy and the code returns, suspicion falls on the relay or the grounds.

Frequently asked questions

Can I drive with P068A?

Yes, gently: the engine usually runs normally. If the code returns for no reason, have it checked.

It appeared after a battery change, is it serious?

Usually not: the battery was disconnected while the ECU was still saving its data. If it doesn't return, nothing more is needed.

Does the ECU need replacing?

Hardly ever. The battery, relay and grounds are checked first.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes